Electrolux Inspiration EWX11831 TC3 Скачать руководство пользователя страница 55

Страница: 55 / 71

Guide to diagnostics of EWX11831 electronic controls

2013 TS/DT-mdm FCPD-dp

55/71

599 77 00-82 Rev. 01

E71

E71: Washing NTC probe faulty

E71

Voltage value out of range (short-circuit or open circuit)

Checks to perform:

Run

phase 7

of the diagnostic cycle

and wait for the water to fill. Switch

the appliance off and measure the

value of the NTC probe between

contacts J3-4 and J3-5 of the wiring

connector

-see fig. 4-.

Is the value correct?

(between 5.7 and 6.3K



at 20°C)

Detach the connector

and measure directly

on the NTC probe.

- (see fig. 18)-

Is the value correct?
(5.7



6.3K



at 20°C)

Run phase

of the

diagnostic cycle,

drain water from the

tub. Replace the

washing heating

element and repeat

the diagnostic cycle

to check for any

further alarms.

Measure between terminals J3-4,

J3-5 of the NTC connector and the

appliance body -

(see fig. 6

Is there any dispersion?

Check/replace the wiring and repeat the diagnostic

cycle to check for any further alarms.

Replace the circuit board and repeat the diagnostic cycle

to check for any further alarms.

Check/replace the wiring and repeat the diagnostic cycle

to check for any further alarms.

Run phase

of the diagnostic cycle,

drain water from the tub. Replace the

washing heating element and repeat
the diagnostic cycle to check for any

further alarms.

Check that all the connectors are correctly inserted

Detach the connector and measure

directly between the terminals of the

NTC probe and the appliance body.

There must be water in the tub.

Has the dispersion been measured?

Fig. 6

MAIN CIRCUIT

BOARD

Heating

element

Temperature

probe

7÷

Ω

(20°



Ω



Ω

5.7÷6.3K

Ω

(20°C)

Fig. 18

If there are burns on the circuit board,

see page 69

Y
E
S

Содержание Inspiration EWX11831 TC3








































































Результаты поиска

Содержание Inspiration EWX11831 TC3

Отзывы:

Бренды по названию

Популярные бренды

Electrolux Inspiration EWX11831 TC3, Руководство по обслуживанию

Результаты поиска

Содержание Inspiration EWX11831 TC3

Отзывы:

Бренды по названию

Популярные бренды