manualshive.com logo in svg

Electrolux Inspiration EWX11831 TC3, Руководство по обслуживанию

Поделиться
Скачать
Electrolux Inspiration EWX11831 TC3 Скачать руководство пользователя страница 18

Guide to diagnostics of EWX11831 electronic controls 

2013 TS/DT-mdm  FCPD-dp 

18/71 

599 77 00-82 Rev. 01

 

 

4.6  Notes on the behaviour of certain alarms 

 

 

Configuration alarm E93: 

when this alarm rings (when turned on) the machine blocks and  the alarm code appears on the display, provided the relevant 

configuration part is intact. 

 

It is not possible to access diagnostics mode and the only available option is to turn the appliance off.

 

 

 

Configuration alarm E94: 

and the code can be viewed from the display.  

The diagnostics mode cannot be accessed and the “quick alarm viewing” mode cannot be used. 

 

 

Alarms

 

EH1-EH2-EH3:

 in the event of problems with the supply voltage, the appliance remains in alarm status until the mains frequency or voltage returns to 

acceptable values or the appliance is switched off (ON/OFF button). Only the 

“H” 

alarm family is displayed if the problem occurs while the appliance is 

working normally, the code is shown simultaneously on the display. 

The diagnostics mode cannot be accessed and the “quick alarm viewing” mode cannot be used: the alarm can only be read in full when the situation has 
normalised. 

 
 
 
 
 
 
 
 
 
 

Содержание Inspiration EWX11831 TC3








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды