ELECTRO FREEZE SLX400E Скачать руководство пользователя страница 47

Страница: 47 / 74

ELECTRO FREEZE Soft Serve Models SLX400E, SLX500

184584

13 Routine Maintenance

(continued)

ANNUALLY

CAUTION

To avoid electrical shock or
contact with moving parts,
make sure the control pad is
“OFF” and that the main power
switch is “OFF”.

1. Contact your Electro Freeze

Distributor for service to replace drive
belts and lubricate the fan motors as
needed.

2. Contact your Electro Freeze

Distributor to clean the inside of the
freezer, including base, side panels,
condenser, etc.

3. Contact your Electro Freeze

Distributor to check water-cooled

condenser and flush clean to remove

scale and deposits if necessary.

SEMIANNUALLY

Contact your Electro Freeze
distributor to replace drive belts.

2. On air cooled and air cooled remote

freezers have your Electro Freeze
distributor check the condenser fan
motor oil.

A. Air Condenser.

Important:
Never use a screwdriver or sharp

object to clean between fins.

Both air and water cooled freezers have

an air condenser. The condenser fins

need to be cleaned by your Electro
Freeze Distributor to remove dirt, lint and
dust.

QUARTERLY

B. Refrigeration System

Have your Electro Freeze Distributor

check the refrigeration system and make
any necessary adjustments.

WARNING!

Failure to properly maintain/clean your air condenser can cause

premature compressor failure. Compressor failure due to improper

condenser care will void the compressor warranty.

Содержание SLX400E










































































Результаты поиска

Содержание SLX400E

Отзывы:

Похожие инструкции для SLX400E

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400E, Руководство оператора

Результаты поиска

Содержание SLX400E

Отзывы:

Похожие инструкции для SLX400E

Бренды по названию

Популярные бренды