ELECTRO FREEZE SLX400E Скачать руководство пользователя страница 30

Страница: 30 / 74

184584

ELECTRO FREEZE Soft Serve Models SLX400E, SLX500

CAUTION
To avoid electrical shock or
contact with moving parts,
make sure the control pad
is “OFF” and that the power
switch is “OFF”.

It is important that the freezer be
disassembled, washed, lubricated and
sanitized before operation.

The cleaning and sanitizing instructions
explained in this manual are required to

Disassembly and Cleaning

maintain a clean, sanitary freezer. The
freezer should be disassembled, cleaned,
reassembled, lubricated and sanitized
daily to ensure the best possible product
quality and freezer operation.

Persons assembling, cleaning, or
sanitizing the freezer must wash and
sanitize hands and forearms with an
approved sanitizer.

8.1

Cleaning Accessories

The following accessories shipped with the freezer are necessary for cleaning,
sanitizing and disassembly/assembly.

1.)

HC150009 BRUSH. & HC158012
HANDLE:

4-inch diameter with 36-inch handle,
used for cleaning the cylinder.

2.)

HC158077 BRUSH:

9/16 inch with 36 inch handle, used
for cleaning the drain tube.

3.)

HC158003 BRUSH:

Double end, 1-1/8 inch diameter
and 7/16 inch diameter, used for
cleaning the mix inlet tube, mix feed
tube, head and general cleaning.

4.)

HC169374 TOOL - O-RING
REMOVAL:

Aids in removing O-rings from
plungers, dispense head, and mix
feed tube.

5.)

HC158000A LUBRICANT -
PETROL GEL:

Approved lubricant for moving
parts and O-rings. See assembly
instructions for lubricating points.

6.)

HC115536 KIT - O-RING.
(NOT SHOWN):

This kit contains all O-rings and seal
needing replacement on a regular
basis.

Figure 8-1 Accessories

HC158009 BRUSH-4” DIA W/O HANDLE

HC158012 HANDLE-BRUSH FIBERGLASS

HC158077 BRUSH-9/16 DIA X 36” HANDLE

HC158003 BRUSH-7/16 & 1-1/8” DOUBLE END

HC158000A
LUBRICANT-PETROL GEL 4 OZ TUBE

HC169374
TOOL-O RING REMOVAL

BRUSH - 4” DIA W/O HANDLE

HANDLE - BRUSH FIBERGLASS

BRUSH - 9/16 DIA X 36” HANDLE

BRUSH - 7/16 & 1-1/8” DOUBLE END

LUBRICANT - PETROL GEL 4OZ TUBE

TOOL - O-RING REMOVAL

Содержание SLX400E










































































Результаты поиска

Содержание SLX400E

Отзывы:

Похожие инструкции для SLX400E

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400E, Руководство оператора

Результаты поиска

Содержание SLX400E

Отзывы:

Похожие инструкции для SLX400E

Бренды по названию

Популярные бренды