ELECTRO FREEZE SLX400E Скачать руководство пользователя страница 53

Страница: 53 / 74

ELECTRO FREEZE Soft Serve Models SLX400E, SLX500

184584

14 Trouble Shooting Tables

(continued)

PROBLEM

PROBABLY CAUSE

REMEDY

Unit operates
long or
continuously.

Dirty condenser.

Have condenser cleaned by your
Electro Freeze distributor.

Shortage of refrigerant.

Contact your Electro Freeze
Distributor for service.

Moisture in system.

Contact your Electro Freeze
Distributor for service.

Compressor failing.

Contact your Electro Freeze
Distributor for service.

Discharge
pressure too
high.

Water hose kinked or pinched. (water
cooled models)

Move freezer and adjust hose so it is
not pinched or kinked.

Water turned off or defective water
regulating valve. (water cooled models)

Turn on water, or contact your Electro
Freeze Distributor for service.

Restricted water cooled condenser.
(water cooled models)

Contact your Electro Freeze
Distributor for service.

Dirty air condenser. (air cooled models)

Contact your Electro Freeze
Distributor for service.

Unit location too warm (air cooled
models)

Contact your Electro Freeze
Distributor for service.

Refrigerant overcharge.

Contact your Electro Freeze
Distributor for service.

Air in system.

Contact your Electro Freeze
Distributor for service.

Discharge
pressure too
low.

Water regulating valve open too wide.
(water cooled model)

Contact your Electro Freeze
Distributor for service.

Shortage of refrigerant.

Contact your Electro Freeze
Distributor for service.

Noisy
compressor.

Tubing rattles.

Contact your Electro Freeze
Distributor for service.

Spring broken internally.

Contact your Electro Freeze
Distributor for service.

Содержание SLX400E










































































Результаты поиска

Содержание SLX400E

Отзывы:

Похожие инструкции для SLX400E

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400E, Руководство оператора

Результаты поиска

Содержание SLX400E

Отзывы:

Похожие инструкции для SLX400E

Бренды по названию

Популярные бренды