ELECTRO FREEZE SLX400C Скачать руководство пользователя страница 53

Страница: 53 / 74

ELECTRO FREEZE Soft Serve Models SLX400C

184582-01

14 Trouble Shooting Tables

(continued)

Compressor will

not start – hums

intermittently

(cycling on

overload)

1. Low line voltage.

Ask power company to increase

voltage to not less than 10% below

data plate rating or have transformer

installed. Have electrician check for

adequate wire size.

2. Improperly wired.

2. Contact your Electro Freeze distributor

for service.

3. Open start capacitor or current relay.

3. Contact your Electro Freeze distributor

for service.

4. High discharge pressure.

4. Contact your Electro Freeze distributor

for service.

PROBLEM

PROBABLY CAUSE

REMEDY

Poor or slow

product recovery.

1. Dirty or blocked condenser, restricted air

flow – high ambient temperature.

Have condenser cleaned by your

Electro Freeze distributor; lower

ambient temperature.

2. Defective condenser fan motor.

2. Contact your Electro Freeze distributor

for service.

3. Component or compressor failure.

3. Contact your Electro Freeze distributor

for service.

Beater motor

does not operate.

1. Head assembly is not installed.

1. Install head assembly.

2. Magnetic head switch defective.

2. Contact your Electro Freeze Distributor

for service.

3. Loose connection in control circuit.

3. Contact your Electro Freeze Distributor

for service.

4. Open starter coil.

4. Contact your Electro Freeze Distributor

for service.

5. Faulty capacitor assembly. (Single phase

only.)

5. Contact your Electro Freeze Distributor

for service.

6. Faulty beater motor.

6. Contact your Electro Freeze Distributor

for service.

Содержание SLX400C










































































Результаты поиска

Содержание SLX400C

Отзывы:

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400C, Руководство оператора

Результаты поиска

Содержание SLX400C

Отзывы:

Бренды по названию

Популярные бренды