ELECTRO FREEZE SLX400C Скачать руководство пользователя

Страница: 39 / 74

ELECTRO FREEZE Soft Serve Models SLX400C

184582-01

10.1

Sanitizing

(continued)

5. Sanitize the inside of the hopper

covers.

6. Reconnect main power supply. Place

the power switch in the “ON” position.

Important:

Do not use the

freeze position with

water or sanitizer in the cylinder. The

freezer will be damaged.

7. When the cylinders have filled with

sanitizing solution, press the soft key

under the

icon and “BEATER

ON” for both sides of the freezer and

allow the beaters to run for 5 minutes.

During this time period, check for

leaks around the head, plungers and

drain tubes.

8. Press “BEATER OFF” on both

sides. Place an empty container

under the dispensing head and drain

the sanitizing solution by opening

the plungers to allow cylinders and

hoppers to empty. Open and close

each plunger at least 10 times during

draining to sanitize the port area of

dispense head.

9. When the sanitizing solution has

drained from the freezer, press the

“OFF” button.

Содержание SLX400C










































































Результаты поиска

Содержание SLX400C

Отзывы:

Похожие инструкции для SLX400C

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400C, Руководство оператора

Результаты поиска

Содержание SLX400C

Отзывы:

Похожие инструкции для SLX400C

Бренды по названию

Популярные бренды