ELECTRO FREEZE SLX400C Скачать руководство пользователя страница 47

Страница: 47 / 74

ELECTRO FREEZE Soft Serve Models SLX400C

184582-01

13 Routine Maintenance

(continued)

ANNUALLY

CAUTION

To avoid electrical shock or

contact with moving parts,

make sure the control pad is

“OFF” and that the main power

switch is “OFF”.

1. Contact your Electro Freeze

Distributor for service to replace drive

belts and lubricate the fan motors as

needed.

2. Contact your Electro Freeze

Distributor to clean the inside of the

freezer, including base, side panels,

condenser, etc.

3. Contact your Electro Freeze

Distributor to check water-cooled

condenser and flush clean to remove

scale and deposits if necessary.

SEMIANNUALLY

Contact your Electro Freeze

distributor to replace drive belts.

2. On air cooled and air cooled remote

freezers have your Electro Freeze

distributor check the condenser fan

motor oil.

Quarterly

1. Have your Electro Freeze Distributor

check the refrigeration system and

make the necessary adjustments.

2. Both air and water cooled freezers

have an air condenser. The

condenser fins need to be cleaned

by your Electro Freeze Distributor to

remove all forms of dirt, lint, and dust.

Important:

Never use a screwdriver or sharp

object to clean between fins.

Содержание SLX400C










































































Результаты поиска

Содержание SLX400C

Отзывы:

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400C, Руководство оператора

Результаты поиска

Содержание SLX400C

Отзывы:

Бренды по названию

Популярные бренды