manualshive.com logo in svg

ELECTRO FREEZE SLX400, Руководство оператора со списком запасных частей

Поделиться
Скачать
ELECTRO FREEZE SLX400 Скачать руководство пользователя страница 34

26

                184584

ELECTRO FREEZE Soft Serve Models SLX400, SLX400E, SLX500

9

Assembly 

 (continued)

Figure 9-4

Head Assembly

8. Install and lubricate the O-rings (4,

figure 9-4) (see O-ring Chart - Replacement
Parts Manual) on the dispensing plungers
(4,5)  and insert half-way into the head (1).

9. Install and lubricate the two 4-inch

head O-rings (2) .

10. Position the handles in the head

assembly by placing the 2 shorter handles
(9) on the sides and the longest handle (10)
in the center. Lock in place with the handle
pin (7).

Important:

Excessive force will damage the head. Do
not use tools to tighten.

11. Install the dispensing head onto the

freezer by aligning the studs with the holes
in the head and sliding toward the freezer.
Tighten hand knobs evenly, finger-tight only.

12. Install the plunger rods (6). The

nozzles (11) will be installed on the mix
outlet at the bottom of the head after
sanitizing.

13. Install the o-rings (3) on the mix

feed tube (1). Lightly lubicate the o-rings as
shown in figure 9-5.

 

— continued

Note

: Item 10 center handle is longer.

Содержание SLX400







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды