ELECTRO FREEZE SLX400 Скачать руководство пользователя страница 3

Страница: 3 / 70

ELECTRO FREEZE Soft Serve Models SLX400, SLX400E, SLX500

WARNING

CAUTION

DANGER

2. Understand Signal Words ....

SAFETY FIRST!

Follow these four steps to safety ....

1. Recognize Safety Information ....Look for this
safety alert symbol throughout this manual.

The signal words —

DANGER, WARNING and

CAUTION

— are used with the safety alert symbol

(DANGER decals on the freezer may or may not
have the safety alert symbol, but the message is
the same). Decals with the words

DANGER

WARNING

CAUTION

appear on the freezer.

DANGER

identifies the most serious hazard.

Decals with the words

DANGER

WARNING

are

typically near specific hazards on the freezer.
General precautions are listed on

CAUTION

safety

decals.

In this manual,

CAUTION

messages with the safety

alert

symbol

call attention to safety messages.

When you see this symbol on your freezer or in this
manual, be alert to the potential for personal injury.
Follow recommended precautions and safe
operating practices.

Содержание SLX400







































































Результаты поиска

Содержание SLX400

Отзывы:

Бренды по названию

Популярные бренды

ELECTRO FREEZE SLX400, Руководство оператора со списком запасных частей

Результаты поиска

Содержание SLX400

Отзывы:

Бренды по названию

Популярные бренды