ELECTRO FREEZE COMPACT Series Скачать руководство пользователя

Страница: 79 / 82

ELECTRO FREEZE Shake Model CS705

184952-01 9/12

Alphabetized Parts List for Model CS705

As Required

LH or RH — Left or right hand is determined as you face the front of the freezer.

NLA No Longer Available

PART

SERIAL NUMBER

DESCRIPTION

NUMBER

QTY

(FROM – TO)

IMPORTANT:
All parts shown are for standard models designed for 208-230v/60Hz/1phase.

Use only original or authorized replacement parts with this freezer.

Use of unapproved parts will void warranty.

O-ring (Mix Feed Tube) ..................................... HC160621 ........... 2 ...... J2O-2935 -

O-ring (Pivot Post) ............................................. HC160555 ........... 2 ...... J2O-2935 -

O-ring (Plunger-Lower) ...................................... HC160582 ........... 1 ...... J2O-2935 -

O-ring (Plunger-Upper) ..................................... HC160501 ........... 1 ...... J2O-2935 -

O-ring (Syrup Line) ............................................ HC160632 ........... 5 ...... J2O-2935 -

Panel-Assy. Front 5 Flavor SH .......................... HC121017 ........... 1 ...... J2O-2935 -

Panel-Assy. Hopper & Top ................................. HC120804 ........... 1 ...... J2O-2935 -

Panel-Dispense 5 Flavor ................................... HC141161 ........... 1 ...... J2O-2935 -

Panel-Rear ........................................................ HC141185 ........... 1 ...... J2O-2935 -

Panel-Side LH CS705 ....................................... HC140659 ........... 1 ...... J2O-2935 -

Panel-Side RH ................................................... HC140658 ........... 1 ...... J2O-2935 -

Plunger-Dispensing 5 Flavor ............................. HC141150 ........... 1 ...... J2O-2935 -

Post-Pivot .......................................................... HC135182 ........... 1 ...... J2O-2935 -

Potentiometer-100K OHM 1-Turn ..................... HC150966 ........... 1 ...... J2O-2935 -

Pulley-Assy. Idler Tensioner .............................. HC120588 ........... 1 ...... J2O-2935 -

Pump-Peristaltic Syrup 24VDC ......................... HC169101 ........... 4 ...... J2O-2935 -

Rectifier-Bridge ................................................. HC150890 ........... 1 ...... J2O-2935 -

Relay-Compressor Start .................................... HC151474 ........... 1 ...... J2O-2935 -

Relay-Control Flange DPDT 24VAC .................. HC150343 ........... 1 ...... J2O-2935 -

Relay-Flange Base w/Cover .............................. HC150381 ........... 1 ...... J2O-2935 -

Relay-Miniature DPDT 230V Coil ...................... HC150097-01 ..... 1 ...... J2O-2935 -

Retainer-Drip Tray ............................................. HC140738 ........... 1 ...... J2O-2935 -

Rod-Actuator ..................................................... HC138611 ........... 1 ...... J2O-2935 -

Rod-Plunger Switch (Actuator Button) .............. HC137760 ........... 1 ...... J2O-2935 -

Sanitizer-Stera-Sheen 4 lb. jar ........................ HC158014A ........ * ...... J2O-2935 -

Sanitizer-Stera-Sheen Case/4 Jars ................. HC158014 .......... * ...... J2O-2935 -

Содержание COMPACT Series



















































































Результаты поиска

Содержание COMPACT Series

Отзывы:

Похожие инструкции для COMPACT Series

Бренды по названию

Популярные бренды

ELECTRO FREEZE COMPACT Series, Руководство оператора

Результаты поиска

Содержание COMPACT Series

Отзывы:

Похожие инструкции для COMPACT Series

Бренды по названию

Популярные бренды