manualshive.com logo in svg

ELECTRO FREEZE COMPACT Series, Руководство оператора

Поделиться
Скачать
ELECTRO FREEZE COMPACT Series Скачать руководство пользователя страница 14

ELECTRO FREEZE Shake Model CS705

184592

4

3.4      Installation Date

Fill in the date of installation, and the name, address, and phone number of the
installer in the space provided below. This information will be needed when ordering
parts or service for the CS705 freezer.

Date of installation:

_____________________________________

Installed by:

_____________________________________

Address:

_____________________________________

_____________________________________

Phone:

_____________________________________

The data plate provides important
information that the operator should
record and have available for parts
ordering, warranty inquiries and service
requests.

Figure 3-1

Fill in the following information as soon as
you receive the 

Electro Freeze

 CS705.

(The item numbers — encircled, below —
correspond with the callout numbers in
figure 4-1.)

1 Model Number: 

_________________

2 Serial Number:

__________________

3 Electrical Spec:

   

Voltage

   ________

Phase 

_______     

Hertz     

_________

4 Maximum Fuse Size: ____________

5   Minimum Circuit Ampacity: _______

Write in Reference
Information HERE!

3.3      Reference Information

3.2     Data Plate

Содержание COMPACT Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды