X10 Home Automation
X10 Home Automation
Introduction
The alarm console is equipped with functions to secure your home. The system uses an intelligent process to control
the lighting in your house, so that it appears as if you are at home. The X10 technology also offers you several so-
called comfort functions. You can e.g. Wireless control lamps connected to Lamp/Dimmer modules with your remote
control or via the keypad on your console. Every lamp or appliance controlled by the system needs to be equipped
with an X10 receiver module. These modules are easy to install (Plug & Play) and are also available separately,
which means you can expand the system as you wish and when you wish.:
!
Blinking Lamps when the larm is trigged.
!
Your lights are switched ON and OFF in such a way that it appears as if you are home.
!
Control lights and electrical equipment by using the remote control.
!
Control lights and other electrical equipment by using the telephone.
A few of the Plug & Play modules::
Lm12
Lamp/Dimmer module Plug-in module to switch and dim lighting.
Am12
Device/Switch module. Plug-in module to switch lighting and electrical equipment.
More information on these modules can be found on www.electia.se or you can contact your local dealer.
Addressing your modules
An adress can be set for every X10 module. This adress consists of a HOUSE CODE (A-P) and a UNIT COD (1-16).
The HOUSE CODE of all your components needs to be set to the same letter code (keep all the HOUSE CODES set
to A. (See page 14). With the UNIT CODE you can give every module its own number, so that they can be
indvidually controlled via keypad or via remote SH600.
Alarm functions of the X10-modules
Four the below functions must the reference adress for the console be A1 and A2. For changing the reference
adress se page 15
Functions of the Lamp/Dimmer modules
!
When Arming the system via the console, the lamps on A1 and A2 will be switched on during the Exit Delay. As
soon as the system is activated, the lamp will be switched off. When Arming the system via remote control, the
lamps will be switched off. When Arming the system via remote control, the lamps will be switched on and off
quickly to indicate the system is activated (comparable to the alarm system of a car). In the case of an alarm the
lights connected to lamp/dimmer modules with addresses A1 cand A2 will flash. After 4 minutes the lights will
remain on.
!
Press on the remote controls
A/B LIGHTS ON/OFF buttons.
The lamps on respective adress A1 or A2 will be
switched On. Press the
A/B LIGHTS ON/OFF
. The lamps on respective adress A1 or A2 will be switched Off.
Comfort functions of the security console
You can also control the modules using the console. If you do not see a menu, the console is in HOME CONTROL
mode. The display shows HOME CONTROL. To control a module with Unit Code 1. Press 1 followed by ON or OFF.
If you want to control MODULE 12, press 1 , then 2, followed by ON or OFF. To control all lamps ON press 0
followed by ON. To control all lamps off press 0 followed by OFF.
Timers
The console can turn on and off lighting and appliances at pre-programmed times, so that it appears as if you are at
home, the so called LIVED IN LOOK. You can also program timed temperature setbacks.
Setting the console mode (software)
1. To access the menu, press the menu upp or menu down button. The display now shows ENTER PIN. Enter your
4-digit PIN code.
2. INSTALL will show up on the display.
4. Use the menu buttons upp/down to go to menu ITEM 7. OPTIONS. Press OK to select this menu item . You can
also go to this menu item directly by pressing a 7 on the number pad.
5. Press “0” on the the number pad. Use the menu buttons
upp/down
to choose
EURO 7 DAY.
Press OK.
6. Press CLEAR again to quit the menu. To confirm your chice, press 1 for Yes or 2 for No. If you choose Yes, you
will quit the menu. If you choose No. You go back to the first menu item.
10
