X10 - Hemautomation
X10 - Hemautomation
Setting Timers
1. To access the menu press the menu upp or down button. The display now shows ENTER PIN.
2.
Enter your 4-digit PIN code (factory setting 0000. See page 12) The display is cleared and shows a * for each
number entered.
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons upp/down to go to menu item 9. SET TIMER. Press OK to select this menu item. You can
also go to this menu item directly by pressing a 9 on the number pad.
5. The display will read NEW TIMER. Press OK.
6. When set to Euro 7-days mode, the display will read 1. Home CNTR and 2. HEAT ICOOL. Select respective timer
to set; either option 1 for control of lights and appliances , or option 2 for timed temperature setbacks. Use the menu
buttons upp/down to check timers you previously set. The top menu item is always called NEW TIMER, unless all 14
timer points have been set.
7. The display will read CHOOSE DAYS. Use the number keys to enter the DAYS, where 1=Monday, 2=Tuesday and
so on. When the days are set,press OK.
8a) The display will read UNIT NUMBER OR THST. Use the number pad to enter the UNIT CODE of the desired
module (1-16) or the Thermostat nr (1-4). Example: If you enter 12, the display will read TIMER 12 ON. The lowest
line will read “:”.
8b). In case the Temperature setback is chosen, an extra chice has to be made, regarding which temperature level
has to be used during the timed event. Choose either COMFORT (which is the comfort level set to the console fo the
respective thermostat), ECONOMY (setback applies for all registered Temperature Zones), or FROST(also applies
for all registered thermostats at once)
9. Enter the time you want the lights to be switched on, or the timed temperature setback has to take place (24 hour
notation). If you make a mistake, press CLEAR. Press ON when you only want to enter the time the lights need to be
switched on.
10. Press OK. The display now reads TIMER 12 OFF. The lowest line will read “:”.
11. Enter the time you want lights to be switched off or the timed temperature setback has to stop.
12. The bottom line on the display now reads 1. WEEKLY
13. Use the menu buttons
upp/down
to select.
1. WEEKLY: The timer setting is executed every week.
2. ONE WEEK: The timer setting is only used one week from today.
3. RANDOM: The timer setting is executed weekly, but varies within the hour entered (if you entered 20:30, the
time may vary between 20:00 and 20:59).
4. ARMED ONLY: The timer setting is only executed when the system is in ARMED AWAY mode.
14. Make your choise and press OK. The display now reads NEW TIMER.
15. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes, you
will quit the menu. If you choose No, you go back to the first menu item.
Clearing the timer settings
1. To access the menu, press the menu upp or down button. The display now shows ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000 see page 12 for changing the PIN code).
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons
upp
and
down
to go to menu item 9. SET TIMER. Press OK to select this menu item. You
can also go to this menu item directly by pressing a 9 on the number pad.
5. The display will read NEW TIMER.
6. Use the menu buttons upp and down to check timers you set before. The timers are shown in the following format:
12 ON 12:40
OFF 18:30
7. When a timer is shown, you can press CLEAR to delete the timer.
8. You need to confirm your choice (CLEAR TIMER). Press 1 for Yes and 2 for No.
9. Press CLEAR again to quit the menu.
11
