Programming of the address for the communication network (
SET ID ADR
) (only for vers. with serial output)
After the confirm with the
A
key of the previous value, the message ID aDR will appear on
F
display; to set the value
that will identify the instrument when it will be connected in a EIA485 communication network, proceed with the
modality, already described. The settable values are from 1 to 247. To confirm, press the
A
key.
Programming of the baud rate (
SET BDR
) (only for vers. with serial output)
The following setting is the baud rate. The message SET appears on
G
display, the message SET BDR on the first
two parts of
F
display to indicate the programming of the baud rate displayed on the third part (L3) o
f
the
F
display. To
modify the value set, it’s necessary to use the
C
key to decrease and
B
to increase the rate. The values settable are:
- 19.2 => 19200 baud
- 9.60 => 9600 baud
- 4.80 => 4800 baud
- 2.40 => 2400 baud
Press
A
to confirm the value displayed.
Programming of the serial parameters (only for vers. with serial output)
8 1
8 data bit / 1 stop bit
PAR
No parity
NO
8 2
8 data bit / 2 stop bit
PAR
No parity
NO
8 1
8 data bit / 1 stop bit
PAR
Even parity
EVE
8 1
8 data bit / 1 stop bit
PAR
Odd parity
ODD
On
G
display will appear the message SET. The following message will appear on
F
display using the
B
and
C
keys.
To confirm press the
A
key.
Programming of the Password (
SET PAS
)
The instrument is supplied without password. When a password (from 0002 to 9999) is set, using the
B
(to increase),
C
(to decrease) and
A
(to confirm) keys, only who know this value can to enter in the setup. The password, in fact, is
required all the time that someone try to enter in the setup (pressing the
A
and
B
key at the same time). If the
password is wrong, the message PASS ERR will appear on
F
display and the instrument go back to the measures
visualization. To input the password, when required by the instrument, at the enter of the setup, use the
A
,
B
and
C
keys as the same way done previously.
The menu is cyclic. After the last setting, the instrument go back to the first page of Setup (SETUP). It’s always
possible to come back to measures visualization mode pressing at the same time the
A
and
C
keys.
PEAK VALUES AND ENERGY COUNTERS RESET (
RESET
)
From the measures visualization mode, pressing the
A
and
C
keys simultaneously the message SETUP will appear
on
F
display, press the key
C
until the message RESET appears on the same display. To accede to the menu, press
the
A
key. Now it’s possible to select the enabling of cancellation type, by pressing the
C
key, according with following
types:
RESET PEA: all maximum value will be delete.
RESET AVG: all average and average maximum value (maximum demand) will be delete.
RESET EN: with NORMAL as energy mode (EN) the total energy counters will be delete, with TOT PAR the
partial energy counters will be delete and with TB1 TB2 the band counters will be delete.
RESET ALL: to delete average maximum values and energy counters.
Entry to menu:
seT UP
Æ
seT Up
RESET
SET DO1
ELM-4D1P
instruction manual
IM443-U v0.7
pag. 8
SET DO2
SET AN OUT
SET HR_
--- OFF OFF
(the visualization depends on the settings and the I/O status)
RESET PEA
NO
/
YES
Confirm Reset
Deleting maximum values (max)
RESET AVG
NO
/
YES
Confirm Reset
Deleting average values (avg)
and maximum demand (maxD)
RESET EN
NO
/
YES
Confirm Reset
Deleting energy counters
RESET ALL NO
/
YES
Confirm Reset
Deleting maximum and average
values, and energy counters
To enable the chosen type, press the
B
key to change the indication on display
G
from NO to yes.
Confirm enabling cancellation, by pressing the
A
key. The indication on display
G
change from yes to ---.
