elco Combi 24 Скачать руководство пользователя страница 51

Страница: 51 / 68

Commissioning

Gas supply

Condensate connection

Connectors for flue gas, air supply and water pressure

Gas supply

Check the connection for the gas

supply to the boiler for a leakproofness.

Possible leaks of must be sealed

before the boiler is started.

De-aerate the gas pipe and the gas

valve.

Request information on the gas type

and values from the local gas supplier,

so as to make sure that the boiler is

operated with the correct gas type.

After assembly of the boiler, all gas-

carrying pipes must be checked for

leaks.

Condensate connection

Make sure that the siphon has been

filled before the boiler is started up, so

as to prevent emission of waste gases

from the condensate connector.

Filling the siphon after assembly.

Removed the siphon (7) from the

condensate connector in the boiler. Fill

it with 0.3 litres of water and then turn it

hand-tight back into its original position.

Flue gas and air supply connections

Check that the connectors for waste

gas and air supply correspond to the

domestic and regional regulations.

Facilities that do not fulfil these

regulations may not be taken into

operation.

Make sure that all connectors are free.

Flue gas and air supply connectors

may not be reduced in size.

Before taking the boiler into

operation, it must be ensured that

dirt particles, which may be present

in the heating facility, are removed

by a thorough flushing of the piping

system.

Water pressure

Open the valves to the system. Check

the water pressure in the system. If the

water pressure is too low (minimum

operating pressure > 1.0 bar), then

it must be increased at least to the

minimum water pressure in the table.

Hydraulic system

Check that the boiler is connected to

hydraulic system in such a way that a

water flow is insured at all times, when

the boiler is in operation. The water

flow is monitored by an ∆T surveillance

in the boiler. A too low flow rate means

that the boiler will stop operating and

be switched off immediately.

Содержание Combi 24





































































Результаты поиска

Содержание Combi 24

Отзывы:

Бренды по названию

Популярные бренды

elco Combi 24, Руководство по эксплуатации

Результаты поиска

Содержание Combi 24

Отзывы:

Бренды по названию

Популярные бренды