•Touch the test probe tips across the part under test.
•Read the capacitance value in the display.
•The display will indicate the proper decimal point and value.
6-10 Measuring Frequency
•Set the function switch to the Hz position.
•Insert the black test lead banana plug into the negative (COM) jack
•Insert the red test lead banana plug into the "V/Hz%/
Ω
/CAP/°C" jack.
•Touch the test probe tips to the circuit under test.
•Read the frequency in the display.
•The digital reading will indicate the proper decimal point, symbols (Hz, kHz,
MHz) and value.
6-11 Measuring Resistance
•Set the function switch to the green
Ω
position.
•Insert the black test lead banana plug into the negative COM jack.
• Insert the red test lead banana plug into the V/Hz%/
Ω
/CAP/°C jack.
•Indicate "OL" "M
Ω
" on the display.
•Touch the test probe tips across the circuit or part under test. It is best to
disconnect one side of the part under test so the rest of the circuit will not
interfere with the resistance reading.
•Read the resistance in the display.
6-12 Measuring Diode.
•Set the function switch to the green position.
•Insert the black test lead banana plug into the negative COM jack and the red
test lead banana plug into the V/Hz%/
Ω
/CAP/°C jack.
•Press the MODE button to indicate and "V" on the display.
•Touch the test probes to the diode under test. Forward voltage will typically
indicate 0.400 to 0.700V. Reverse voltage will indicate "Or. Shorted devices
will indicate near OV and an open device will indicate "OL" in both polarities.
6-13 Audible Continuity Test
•Set the function switch to the green position.
•Insert the black lead banana plug into the negative COM jack. Insert the red
test lead banana plug into the V/Hz%/
Ω
/CAP/°C jack.
•Press the MODE button to indicate " " and "
Ω
" on the display
•Touch the test probe tips to the circuit or wire you wish to check.
•If the resistance is less than approximately 50
Ω
, the audible signal will sound.
If the circuit is open, the display will indicate "OL”
6-14 Non-contact AC Voltage Test (NCV)
•Set the function switch to the ON position.
• Remove the meter and face the NCV detector to ACV source.
•If source voltage in 200-1000V the NCV indicate lamp will light.
7.Maintenance
Battery and Fuse Replacement If the sign " " appears on the LCD display, it
indicates that the battery should be replaced. Remove screws on the back
cover and open the case. Replace the exhausted battery with new batteries.
(1 x 9V battery NEDA 1604, 6F22 or equivalent)
Fuse rarely need replacement and blow almost always as a result of the
operator's error. Open the case as and replace the blown fuse with ratings
specified.
Warning: Before attempting to open the case, be sure that test leads have
been disconnected from measurement circuit to avoid electric shock hazard.
Replace fuse only with specified ratings:
Fuse 1 : F1OA / 250V fast blow.
Fuse2: F500mA / 250V fast blow.
Information for users:
The symbol on the equipment indicates that the waste must be “separately
collected”.
Therefore, the user must carry (or have it carried) the waste to the separately
collected waste centers set up by local governments, or deliver it to the dealer
against purchase of a new equivalent-type equipment.
The separate waste collection and the subsequent processing, recovery and
disposal operations favour the production of equipment with recycled
materials and limit the negative effects on the environment and on health
which may be possibly caused by the waste improper management.
The
improper
product
disposal
by
the
user
causes
the
application
of
administrative
sanctions
according
to
the
Art.
50
et.
seq.
of
the
Law
Decree
No.
22/1997.
IMPORTED AND DISTRIBUTED BY
ELCART DISTRIBUTION SPA
Via Michelangelo Buonarroti, 46
20093 COLOGNO MONZESE (MI)
ITALY
www.elcart.com - [email protected]
ELCART DISTRIBUTION SPA via Michelangelo Buonarroti, 46 - 20093 Cologno Monzese (Milano) ITALY
Tel. ++39(0)2/25.11.73.10 Fax ++39(0)2/25.11.76.10 sito internet: www.elcart.com e-mail: [email protected]
La divulgazione dei dati contenuti in questa scheda è da ritenersi un servizio puramente informativo e non costituisce alcun vincolo da parte della Elcart in merito a prestazioni ed utilizzo del prodotto.
