background image

 

6. Operating Instruction  

6-1 Measuring Sound Level  
•Set the function switch to the green "dB" position.  
•Remove the meter and face the microphone to sound source in a horizontal 
position.  
•The C-weighting curve is nearly uniform over the frequency range from 30 to 
10,000Hz, thus giving an indication of overall Sound level.  
•The Fast response is suitable to measure shout bursts and peak values from 
sound source.  
•The sound level will be displayed.  
Note: Strong wind (over 10m/sec.) striking the microphone can cause 
misreading for measurement in windy locations, a windscreen should be used 
in front of microphone.  
6-2 Measuring Humidity  
•Humidity Measurement for indoor.  
•Set the function switch to the ON position.  
•Remove the meter place to the room. 
•Read the %RH in the display for about two hours.  
6-3 Measuring Light  
•Set the function switch to the green "Lux" scale and set the range to desired 
("Lux" or "x10 Lux") range.  
•Remove the meter and face the photo detector to light source in a horizontal 
position.  
•Read the illuminance nominal from the LCD display.  
•Over-range: If the instrument only display one "1" in the M.S.D. the input 
signal is too strong, and a higher range should be selected.  
•When the measurement is completed. Replace the photo detector from the 
light source.  
•Spectral sensitivity characteristic: To the detector, the applied photo diode 
with filters makes the spectral sensitivity characteristic almost meet CIE. 
(International Commission on Illumination) photopia curve V ( 

λ

) as the 

following chart described. 

 

Recommended Illumination:  
Locations 

 

    Lux 

 

*Office  
Conference, Reception room.    

 

200 to 750 

Clerical 

work 

 

    700 

to 

1,500 

 

Typing 

drafting 

 

    1000 

to 

2,000 

 

*Factory  
Packing work, Entrance passage 

 

150 to 300  

Visual work at production line    

 

300 to 750 

Inspection 

work 

    750 

to 

1,500 

Electronic parts assembly line    

 

1500 to 3,000 

*Hotel  
Public room, Cloakroom  

 

 

100 to 200  

Reception, 

Cashier 

 

   200 

to 

1,000 

*Store  
Indoors Stairs Corridor   

 

 

150 to 200  

Show window, Packing table    

 

750 to 1,500 

Forefront of show window  

 

 

1500 to 3,000 

*Hospital  
Sickroom, 

Warehouse 

 

   100 

to 

200 

 

Medical Examination room  

 

 

300 to 750 

Operating room Emergency Treatment   

750 to 1,500 

*School  
Auditorium, Indoor Gymnasium   

 

100 to 300   

Class 

room 

 

    200 

to 

750 

Laboratory Library Drafting room  

 

500 to 1,500 

 
 
 

ELCART DISTRIBUTION SPA  via Michelangelo Buonarroti, 46 - 20093 Cologno Monzese (Milano) ITALY

Tel. ++39(0)2/25.11.73.10 Fax ++39(0)2/25.11.76.10 sito internet:  www.elcart.com    e-mail: [email protected]

La divulgazione dei dati contenuti in questa scheda è da ritenersi un servizio puramente informativo e non costituisce alcun vincolo da parte della Elcart in merito a prestazioni ed utilizzo del prodotto.

Содержание Nimex NI-8002

















Отзывы: