background image

SURFACE MOUNT LEDFIRE III EMERGENCY INSTALLATION INSTRUCTIONS

DRAFT

14

27. Warranty information

Ektor products are distributed in Australia and New Zealand by Evolt Pty Ltd (

Evolt

). 

The Australian Consumer Law as well as other Australian laws guarantee certain conditions, warranties and 
undertakings, and give you other legal rights, in relation to the quality and fitness for purpose of Ektor products 
sold in Australia. 

In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You 
are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable 
loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable 
quality and the failure does not amount to a major failure. What constitutes a major failure is set out in the 
Australian Consumer Law.

Nothing in this Warranty purports to modify or exclude the conditions, warranties and undertakings, and other 
legal rights, under the Australian Competition and Consumer Act and other Australian laws. 
Ektor products are warranted in Australia for a period of 12 months from the date of delivery of the product, 
provided that the products are properly stored, installed, used and maintained in accordance with the instructions 
contained within their manual. 

Products that have been altered in any way or used other than in accordance with their instructions are not 
covered by this warranty. 

This warranty is not transferrable and is valid only in the hands of the purchaser of the product. The warranty 
does not cover Ektor products other than those purchased from Evolt. Proof of purchase must be provided to 
Evolt with any warranty claim. Evolt recommends that the purchaser attaches their proof of purchase to their 
product manual.

Evolt’s total liability under this warranty is limited to the cost of repair or replacement of the faulty product. Evolt 

may satisfy its obligations under this warranty in full by repair or replacement of a faulty product. 
This warranty does not apply to consumable items such as lamps or batteries or other items that can be classified 
as consumable. 

For the avoidance of any doubt, any and all warranties or conditions which are not guaranteed under the 
Australian Competition and Consumer Act or the Australian Competition and Consumer Regulations 2010 and 
which are not expressly included in this Warranty as additional warranties or conditions are excluded.

This Warranty does not cover loss or damage caused by wear and tear, misuse, incorrect installation or 
operation, failure to clean and maintain, incorrect voltage or non-authorised electrical connections, adverse 
external conditions (such as power surges and dips, acts of God, exposure to heat, corrosion, insect or vermin 
infestation), use of non-authorised or defective parts or globes, or to items that have been repaired other than by 
Evolt or a repairer approved by Evolt. 

Содержание EV-LEDFIRE-III-SM

















Отзывы: