background image

SERVICE MANUAL

 

 

SM-eVENT-GB-3_8-2006.doc

 

9

 

5.5. 

First putting into operation  

• 

Check whether all fixing screws used during transport were removed.  

• 

Check that the connections of the compressed air supplies are correct.  

• 

Check for proper connection to the mains supply.  

• 

Switch on the pressure switch (6) to position “I”. 

 
After first putting the compressor into operation, the air chamber of compressor is pressurized to a 
‘switching-off’  pressure  and  the  compressor  will  then  be  automatically  switched  off.  During  the 
following  time  period  the  compressor  works  in  an  automatic  mode,  i.e.  according  to  the 
consumption of compressed air, the compressor is switched on and off by the pressure switch.  
During  the  operation,  the  appliance  releases  condensed  water  from  the  condenser  (filter) 
automatically to the evaporative tray (20). 

 

5.6. 

Additive accessory 

• 

Tube for supporting equipment 

is suitable for gripping of respiratory apparatus with accessories. Please remove the plug in the 
middle of the upper side before installation. Screw the tube into the socket and tighten it fast. 
 
Technical data:  
diameter   

25 mm 

height 

 

1100 mm above the floor 

 

Max.  tube  loading  accepted  is  18  kg.  The  centre  of  gravidity  of  supporting 
equipment must be in the axis of the tube, max. 1100 mm above the floor. Other 
connecting  consult  with  manufacturer.  Producer  recommends  an  supporting 
equipment disassemble before transport . 

6.  PERSONNEL (SEE ANNEX) 

In  the  case  of  danger,  switch  the  appliance  off    at  the  switch    and  pull  out  the 
mains plug. 

Automatic  operation.  When  the  pressure  in  pressure  tank  falls  down  to  a  ‘switch  on’ 
pressure, the compressor is automatically switched on. The compressor is automatically 
switched off when the pressure increases to the ‘switching off’ pressure in the pressure 
tank. 

6.1. 

Switch on compressor 

The compressor is switched on by mains switch (6) by putting it to position „I“. Switching on of the 
compressor is signaled by the green indicator (4). 
 

6.2. 

 Running on compressor 

When the pressure of the air at the ‘Inlet’ port is reduced or if there is a reduction of pressure in 
the air chamber, the compressor is switched on and the air chamber is filled with compressed air. 
After  the  ‘switching-off’  pressure  is  reached,  the  compressor  is  automatically  switched  off. 
Pressure of the output air from compressor  indicates the manometer (1). 
During the operation of the compressor, the pointer of the humidity indicator (2), should be in the 
green  zone.  If  the  consumption  of  air  from  an  appliance  is  larger  that  the  maximal  outflow,  the 

 

PDF created with pdfFactory trial version 

www.pdffactory.com

Содержание DK50 D






























Отзывы: