EKKO ES100E Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 65

background image

Work Area Safety

9

Tip-over Hazards

Occupants, equipment and materials shall not

exceed the maximum platform capacity or the

maximum platform capacity of the platform

extension.

Model

Platform

retracted

Extension

only

Maximum

occupants

ES40E

500 lbs

220 lbs

Indoor

-2P

ES60E

500 lbs

260 lbs

Indoor

-2P

Outdoor

-2P

ES80E

990 lbs

260 lbs

Indoor

-2P

Outdoor

-1P

ES100E

700 lbs

260 lbs

Indoor

-2P

Outdoor

-1P

ES120E

700 lbs

260 lbs

Only
indoor-2P

Maximum occupants Platform retracted

Platform only

Do not raise the platform unless the machine
is on a firm, level surface.

Do not drive over 0.8 km/h with the platform
raised.

Do not depend on the tilt alarm as a level
indicator. The tilt alarm sounds on the chassis
only when the machine is on a severe slope.

If the tilt alarm sounds:

Lower  the  platform.  Move  the  machine  to  a
firm,  level  surface.  If  the  tilt  alarm  sounds
when  the  platform  is  raised,  use  extreme
caution to lower the platform.

Outdoor Use: Do not raise the platform when
wind speeds may exceed 12.5 m/s. If wind
speeds exceed 12.5 m/s when the platform is
raised, lower the platform and do not continue
to operate the machine.

Indoor Use: When raising the platform, follow
ratings for allowable side force and number of
occupants on the right.

Do not operate the machine in strong or gusty
winds. Do not increase the surface area of the
platform or the load. Increasing the area
exposed to the wind will decrease machine
stability.

Do not drive the machine on or near uneven
terrain, unstable surfaces or other hazardous
conditions with the platform raised.

«
...
9
10
11
12
13
...
»

Содержание ES100E


































































Отзывы:

Нет отзывов

Похожие инструкции для ES100E

Бренд: jcb Страницы: 200

CPCD30/35-XW43E-RT

Бренд: HANGCHA Страницы: 103

Бренд: KAUP Страницы: 28

Power Stak PPS2200-62NFO-27

Бренд: Presto Страницы: 32

Бренд: NIFTYLIFT Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды