EKKO ES100E Скачать руководство пользователя страница 41

Страница: 41 / 65

Maintenance

Observe and Obey:

√ Only routine maintenance items specified

in this manual shall be performed by the

operator.

√ Scheduled maintenance inspections shall

be completed by qualified service technicians,

according

the

manufacturer

’

specifications and the requirements specified

in the responsibilities manual.

Maintenance symbol legend

The following symbols have

been

used

this

manual

help

communicate the intent of the instructions.

When one or more of the symbols appear at

the beginning of a maintenance procedure, it

conveys the meaning below:

Indicates that tools will be required to

perform this procedure.

Indicates that new parts will be

required to perform this procedure.

Indicates that dealer service will be

required to perform this procedure.

Inspect the Batteries

Proper battery condition is essential to good

machine performance and operational safety.

Improper fluid levels or damaged cables and

connections can result in component damage

and hazardous conditions.

Note: Sealed battery or maintenance free

batteries machine, do not need to check this

matter.

Electrocution hazard

Contact with electrically charged circuits

could result in death or serious injury.

Remove all rings, watches and other jewelry.

Bodily injury hazard.

Batteries contain acid. Avoid spilling or

contacting battery acid. Neutralize battery

acid spills with baking soda and water.

Note: Perform this test after fully charging the

batteries.

1. Put on protective clothing and eye wear.

2. Be

sure

that

the

battery

cable

connections are free of corrosion.

3. Be sure that the battery lock bar is in

place and secure.

4. Remove the battery vent caps

5. Check the battery electrolyte level. If

necessary, added to distilled water from

the bottom of the storage battery

charging tube. Do not add too much.

6. Place the vent cap back.

Note: Adding terminal protectors and a

corrosion preventative sealant will help

eliminate corrosion on the battery terminals

and cables.

Содержание ES100E


































































Результаты поиска

Содержание ES100E

Отзывы:

Похожие инструкции для ES100E

Бренды по названию

Популярные бренды

EKKO ES100E, Руководство оператора и по обслуживанию

Результаты поиска

Содержание ES100E

Отзывы:

Похожие инструкции для ES100E

Бренды по названию

Популярные бренды