EKKO ES100E Скачать руководство пользователя страница 21

Страница: 21 / 65

Controls

Platform control panel

1 Thumb rocker switch for steer function

Press both of the thumb rocker and the
machine will turn in the direction the blue
triangle points on the platform control panel.

2 Drive function button

Push this button to activate the
drive function.

3 Drive speed select button

Press this button to activate the
slow drive function. The indicator
light will be on when slow drive is
selected.

4 Red Emergency Stop button

Push in the red Emergency Stop button to the
off position to stop all functions. Pull out the
red Emergency Stop button to the on position
to operate the machine.

5 Horn button

Press the horn button and the horn will sound.
Release the horn button and the horn will not
sound.

6 Lift function button

Push this button to activate the lift function.

7 LED

LED diagnostic readout, battery charge
indicator and lift/drive mode
indicator

8 Proportional control handle
and function enable switch
for drive and lift functions

Lift function: Press and hold the function

enable switch to enable the lift function on the

platform control handle. Move the control

handle in the direction indicated by the blue

arrow and the platform will raise. Move the

control handle in the direction indicated by the

yellow arrow and the platform will lower. The

descent alarm should sound while the platform

is lowering.

Drive function: Press and hold the function

enable switch to enable the drive function on

the platform control handle. Move the control

handle in the direction indic

ated by the bl

arrow on the control panel and the machine

will move in the direction that the blue arrow

points. Move the control handle in the

direction indicated by the yellow arrow on the

control panel and the machine will move in the

direction that the yellow arrow points.

Note:

You will wait 10 seconds to operate the

machine when you turn on key switch

every time

Содержание ES100E


































































Результаты поиска

Содержание ES100E

Отзывы:

Похожие инструкции для ES100E

Бренды по названию

Популярные бренды

EKKO ES100E, Руководство оператора и по обслуживанию

Результаты поиска

Содержание ES100E

Отзывы:

Похожие инструкции для ES100E

Бренды по названию

Популярные бренды