Efcon omy Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 48

Efcon omy Скачать руководство пользователя страница 8

Installation & User Manual - Sampling Systems

Version 140618 UK

Page 8

R

E

f

con

Carry-Box Enclosure

A)

Handle

B)

Operating panel

C)

Vacuum chamber

D)

Pincher

E)

Splash board

F)

Connectors

G)

Power supply

H)

Suspension bracket

2.3

Installation

2.3.1

Mechanical

First determine where the sampler must be placed (in case of an ILS
system) before installing the enclosure. This way you can check if the
sample hose (from sampler to enclosure) has a gradual slope.

Efcon









omy enclosure

Place the enclosure on a firm horizontal (water-levelled) ground and fix
the enclosure with the two supplied SS mounting brackets, bolts and
plugs.

BE CAREFULL!

Don’t turn the M6 bolt too tight in the enclosure.

Beneath the enclosure a condensate drain outlet is fitted. The outlet has a
push-in fitting for 8 mm tubing. See fig. 2.3a.

Carrybox enclosure

This enclosure is only available for vacuum and peristaltic samplers.
Mount ±300 mm DIN-rail horizontal to the wall on which the enclosure is
placed. Make sure there is sufficient height for an gradual, siphons free
and nod free sample drain to the container.

A

D

D

A

B

C

E

F

F

H

Fig. 2.3a

Fig. 2.2b

G

«
...
6
7
8
9
10
...
»

Содержание omy

















































Отзывы:

Нет отзывов