Efcon omy Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 48

Efcon omy Скачать руководство пользователя страница 21

Installation & User Manual - Sampling Systems

Version 140618 UK

Page 21

Revision Vacuum samplers

When the capacity of the air pump decreases, the filters inside the pump
need to be cleaned. Remove the pump from the electronic compartment.
Loosen the four M4 bolts from the pump head and remove the 2 filters
(D) from the pump head. Clean the filters with tap water and let them dry.

Be aware!

Reassemble the pump exactly as seen in fig 4.6a.

Replacing pincher

•

Remove power supply

•

Loosen the connector bolt (E) from the pincher connector (D) by
hand. Remove the white bolt (F) which holds the silicon
hose and loosen the nut (B) from the enclosure (A).

•

Remove the pincher and replace the new pincher.

•

Place the connector seal (C) and connector (D) and fasten the
connector bolt (E) (

Be aware! Seal air tight

).

•

Place de white bolt back in its position.

•

Connect the power supply, check if the pincher works properly.

4.7

Trouble shooting

Problem

Diagnose

Solution

Sampler doesn’t take any
samples

Check sampling settings

§3.5

End of suction hose not
emerged

See installation instructions
(

§4.3)

PP glass holder loose

Fasten glass holder

Coupling suction hose leaks
air

Fasten / replace coupling
suction hose / replace
O-ring

Air pump not enough power Check pump filters and

rotor blocks(

§4.6)

Pincher doesn’t fully pinch
the silicon hose

Adjust the pot meter on the
power supply to 24 ± 0,10
VDC

To high pulse frequency

Max. pulse frequency:
< 1 pulse / second

Air pump rotates but doesn’t
blow air

Rotor block inside pump is
broken / worn down

Replace rotor block
(

§4.6)

Sampler skips suction

Polluted Pins inside sample
chamber

Clean all wetted parts
inside the sample chamber

Low sample volume

Sample volume to low
adjusted

Lengthen silicon hose
(

§4.5)

Medium enters sample
chamber to quickly

Contact your supplier

Fig. 4.6a

Fig. 4.6b

F

A

B

C

D

E

«
...
19
20
21
22
23
...
»

Содержание omy

















































Отзывы:

Нет отзывов