Efcon omy Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 48

Efcon omy Скачать руководство пользователя страница 38

Installation & User Manual - Sampling Systems

Version 140618 UK

Page 38

9.3

Principle of operation

1)

Purge:

When taking a sample the sampler starts purging the suction

hose during a set time (parameter Purge time, default 8 seconds). This
is to remove the old medium from the suction hose trough the inlet.

2)

Suction:

The samplers starts creating a vacuum on the inlet until

medium reaches the medium detector (A in fig 9.3a). When the
sampler doesn’t detect the medium within a set time (parameter Max
Suction time, default 30 seconds), an error sample is counted.

3)

Dose:

After the medium is detected the sampler doses the medium

during a set time (Dose time: 8 seconds default).

4)

Rinse:

When a sample is dosed, the peristaltic pump creates pressure

again on the inlet to rinse all the excess water from the tubing inside
the pump and suction hose all during a set time (Parameter RinseT,
default 10 seconds).

9.4

Installation instructions

Follow the following procedures during installation:

•

Connect the suction hose to the supplied suction hose coupling..
Feed the hose through the inlet and fasten the gland air tight.

•

Mount the end (inlet) of the suction hose on a fixed

representative turbulent point to sample homogeneous

wastewater. Ensure the suction hose is always emerged in the
wastewater / medium.

Keep in mind:

•

Maximum suction height: 8 meter

•

Maximum suction length: 30 meter

Purge

Suction

Dose

Rinse

Fig. 9.3a

«
...
36
37
38
39
40
...
»

Содержание omy

















































Отзывы:

Нет отзывов