Efcon omy Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 48

Efcon omy Скачать руководство пользователя страница 11

Installation & User Manual - Sampling Systems

Version 140618 UK

Page 11

2.4

Maintenance

Be aware! Switch off power supply before maintenance or revision.
Remove compressed air couplings and remove pressure and medium
from wastewater piping.

Maintenance and reparations should be done by qualified personnel.

Avoid direct contact with wastewater. Wear protective gloves during use,
maintenance and reparations.

The maintenance frequency depends on wastewater characteristics. Clean
(or replace if necessary) all parts which come in contact with the sampled
medium regular.

Check  if  the  cool  shaft  of  the  cooler  is  clean  /  not  clogged  by  dust.
Cleaning  the  enclosure  can  be  done  with  a  moist  cloth,  but  avoid  all
electrical parts.

Check annually if the screws of all the electronic connection are tightened.

2.5

Trouble shooting

Problem

Diagnose

Solution

Cooler freezes the
containers

Wrong settings controller
Door not closed
Door “leaks” air

24VDC circuit out of
range

Check setting (

§3.5.7)

Close door, check rubber
seal of the door with a
flash light.
Adjust the pot. meter on
the power supply to
24,00 VDC ±0,10 VDC.

Cooler doesn’t cool

Wrong settings controller
Fan inside the protection
cover doesn’t work

Check settings (

§3.5.7)

Check / replace fan

Distributor does not turn
(properly)

Wrong distributor
settings

Check settings (

§3.5.7)

Hex. bolt on the
distributor engine is loose

Fasten bolt

Silicon hose doesn’t turn
free in rotation

Shorten silicone hose

«
...
9
10
11
12
13
...
»

Содержание omy

















































Отзывы:

Нет отзывов