Edco ASB-14 Скачать руководство пользователя страница 15

MPS-I-0819

Page 14

Page 15

MPS-I-0819

E-SPTS-I-0809

800-638-3326 • edcoinc.com • [email protected]

800-638-3326 • edcoinc.com • [email protected]

EQUIPMENT DEVELOPMENT CO., INC.

EQUIPMENT DEVELOPMENT CO., INC.

Changing Blades - 

On EDCO saws in this manual

  

Disconnect the machine from the power source before performing any work on the equipment (i.e. changing 

the blade). To disconnect the power source on gasoline engine models, remove the spark plug lead. On electric 

models, unplug the electrical power cord at the machine.

•  Make sure you have the proper blade for the job. Determine the hardness and composition of the slab. Give your dealer  

 

complete information including whether re-bars are present, the desired depth of the cut, and length of the cut. If in doubt,  

 

contact the blade manufacturer.

 

 

Inspect the blades before installing. Check diamond blades for cracks, loose segments and oversize, worn, or  

 

 

out-of-round arbor holes 

(On page 17)

. Do not use 

any

 questionable blade since serious personal injury and/or  

  damage to property can result. Do not use warped, twisted, or out-of-balance blades. Unbalanced  

 

  blades will wear excessively, vibrate and damage both arbor shaft and bearings. Do not use blade without a  

   drive pinhole 

(Figure 10).

 

 

For safety reasons, EDCO 

does not

 recommend the use of any abrasive blades. Abrasive blades can break  

 

 

and cause  serious personal injury to operator and/or bystanders. If abrasive blades are used by choice, use  

 

 

only reinforced abrasive blades. Inspect blades carefully.

  Never exceed the maximum operating speed of the blade. Be sure to match the blade speed rating with the  

  arbor shaft speed on the machine. The standard models of the SK-14, SB-14, DS-18 have an arbor shaft  

  speed (unloaded) of 3600 RPM and 3000 RPM under load.

 

•  Do not remove or lift the blade guard unless machine is stopped and all power is disconnected. Be sure to reinstall blade  

 

guard before reconnecting the power source.

•  Be sure the arbor shaft, backing plate, and blade cap are clean and in good condition. Make sure the threads are clean and  

 

undamaged. If any damage is detected, consult your EDCO dealer 

(or the EDCO factory)

.

  

 

•  The backing plate and blade cap 

(Figure 11)

 should be the same diameter, do not use if they are different diameters. For  

 

abrasive blades and for all steel centered diamond blades, the backing plate and blade cap must be at least 1/4 the  

 

diameter of the blade.

•  The drive pin should be tight in the blade cap and long enough to fit through blade and into hole in backing plate.

•  Place the blade on the arbor shaft and turn until the drive pinhole lines up with the backing plate.

•  Place the blade cap on the arbor shaft so the drive pin goes through the holes in the blade and backing plate.

•  Put washer and arbor shaft nut and tighten arbor shaft nut.

•  Secure the blade guard in the operating position before reconnecting the power supply or starting engine.

Arbor Shaft

Figure 11

Blade Cap

retaining Nut

Blade Retaining 

Cap

Backing Plate

Drive Pin

Drive Pin Hole

Internal tooth

Lock Washer

Figure 10

Drive Pin Hole

Содержание ASB-14





















Отзывы: