Edco ASB-14 Скачать руководство пользователя страница 13

MPS-I-0819

Page 12

Page 13

MPS-I-0819

E-SPTS-I-0809

800-638-3326 • edcoinc.com • [email protected]

800-638-3326 • edcoinc.com • [email protected]

EQUIPMENT DEVELOPMENT CO., INC.

EQUIPMENT DEVELOPMENT CO., INC.

Operating Instructions

• 

FOR WET CUTTING:

  Attach the water supply.  A flow rate of approximately 2 gallons per minute (minimum) is

  required.  Attach the water hose to the coolant valve.  Use the valve to control the flow of water.  

• 

FOR DRY CUTTING:

  Provide a respirator and dust control system.

• 

FOR ELECTRIC MODELS: 

 Be sure the “OFF” button is depressed.  Hook up the electrical power source by

  plugging into the connector provided.  If the cord does not mate with the connector, consult a qualified licensed  

  electrician before continuing.  Be sure that the equipment is properly grounded.

• 

FOR GASOLINE MODELS:

  Put the engine stop switch in the “RUN” position.  Consult the engine manufacturers  

  operating instructions and follow the directions for starting and breaking in the engine.

• 

FOR PNEUMATIC MODELS:

  Before connecting the air source, be sure the “WHIPCHEK

TM

” cable is

  properly installed and the flow control lever is in the “OFF” position.  Adjust the air pressure to 90 psi (100 psi MAX.)

 

using the air regulator valve 

(see Figure 4 on page 6)

.  Open the flow control lever gradually to start and adjust the  

  oil regulator knob as required for your application.

Before Starting Engine:

• 

BEFORE STARTING THE ENGINE OR MOTOR:

  Raise the saw blade clear of the working surface. The blade is  

  raised using the depth control handwheel knob mounted on the upper handle assembly 

(Figure 5). Lift the knob to  

  unlock and turn the handwheel clockwise until the blade is clearly off the ground.

• 

START ENGINE AND ALLOW IT TO REACH OPERATING SPEED: 

 Position the saw over the cutting line.    

 

Bring the engine to full speed. Lower the blade into the slab surface by slowly turning the depth control handwheel  

 

knob.   

NOTE 

- the 14 inch blade has a maximum cutting depth of 4 3/4”.  Do not allow the arbor flanges to contact  

  slab surface.

  When the selected cutting depth is reached, lock the depth control

  handwheel knob and proceed to push the saw forward.  The saw

  blade must remain straight, do not twist, and do not force blade,

  the engine or motor should not strain when cutting.

  Cutting to maximize depth should be achived in stepped

  increments of 1”.

Refer to the 

Rx for Diamond Blades 

for more detailed information on diamond blades.

Figure 5

Depth Control 

Handwheel Knob

Содержание ASB-14





















Отзывы: