Edco ASB-14 Скачать руководство пользователя страница 14

MPS-I-0819

Page 14

Page 15

MPS-I-0819

E-SPTS-I-0809

800-638-3326 • edcoinc.com • [email protected]

800-638-3326 • edcoinc.com • [email protected]

EQUIPMENT DEVELOPMENT CO., INC.

EQUIPMENT DEVELOPMENT CO., INC.

Optional Accessories

Optional Water Tank Kit for 

SK-14 (P/N 52075),

SB-14 (P/N 51090), 

DS-18 (P/N 56310).

DS-20 (P/N 56310).

KL-18 (P/N 56310)

**KL-18 Requires optional 

lifting bail for Water  

Tank Kit assembly**

Model SK-14, with WaterTank Option, shown

 

TO STOP THE MACHINE: 

 Stop forward motion.  On gasoline models push the throttle to idle.  Turn the

 

depth control handwheel knob counter clockwise to raise the blade clear of the cut.  Turn ignition or power

      switch off and let the engine come to a complete stop.  Turn off the water supply.

 

WHEN MANEUVERING THE SAW:

  Make sure the blade is raised high enough so it does not strike the    

 

slab surface.  Damage to blade may occur with inadvertent contact with the slab or other object.

 

DO NOT FORCE BLADE WHILE CUTTING. 

 

IF THE POWER SOURCE STALLS IN THE CUT: 

 Raise the blade completely out of the cut.  Disconnect

      the  power source (i.e. the spark plug wire on a gasoline engine or disconnect an electric model at the ma-

      chine).  Inspect the blade flange nut/bolt to verify that they are still tight, and inspect the blade for damage.  

      Replace damaged (or questionable) blades immediately.

 

WHEN TRANSPORTING THE SAW:

  Be sure to remove the blade. Before removing the blade, 

 

disconnect the power source before lifting or removing any guard.  

 

See the directions for Installing Blades on 

(page 15)

.

 

WHEN HOISTING A CONCRETE SAW EQUIPPED WITH A LIFTING BAIL:  

Always inspect frame and

Figure 6

Operating Instructions

Содержание ASB-14





















Отзывы: