55
EN
DO NOT MOUNT THE FAN ON A SUSPENDED CEILING,
MINERAL WOOL BOARDS OR PLASTERBOARD, ETC.
Choose a location for the fan where the blades are at a
minimum distance of 2.35m from the ground. Mount the
support plate on the ceiling, or the plate already in use. In
order to fasten the plate correctly, use two self-threading
screws, to fix the plate to the beam or joist. If the place you
have chosen does not have a suitable beam for fastening,
install a 5 x 10 cm base between the ceiling joists to support
the fan.
1.- Attach the plate with the two screws included with the fan.
2.- Attach the plate with the two screws included with the
fan.
2.- Hang the fan on the hook on the decorative cover,
through a hole in the light fixture.
3.- Make electrical connections.
(See connection instructions)
4.- Secure the light fixture in the middle to the decorative
cover with the four screws provided. Turn the light fixture in an
anti-clockwise direction if necessary, to ensure that it is
securely installed.
5.- Attach each blade to its holder using three screws per blade.
Then attach the holders to the fan using two screws per
holder.
6.- Attach the anchoring elements
INSTRUCTIONS FOR USE
The operating sequence when pulling the chain is:
OFF(0)-MAXIMUM(3)-MEDIUM(2)-MINIMUM(1)
• Fan switch (winter / summer mode ): the fan rotates to
the right in one position and to the left in the other. This
means that the blades take in the air from above and push it
downwards or act as an extractor (taking in air from below to
push it upwards).
• Although your fan has been installed more than 2.35
metres above the ground, be careful when lifting objects near
to the blades.
• Light switch The operating sequence when pulling the chain
is:
OFF-ON
The remote control is provided with 2 batteries R6 (AA), 1.5 V each.
- Remove the cover from the battery compartment located
at the back of the remote control.
- Insert the batteries according to their polarity (following the
s and –) .
- Replace the battery compartment cover.
The remote control is used to switch the fan on and off
(Figure 1).
1. FAN SWITCH-ON To switch the fan on,
press button “0” and then release it. To switch
the fan off, press button “0” again and then
release it.
2. SPEED The fan speed can be adjusted to
the desired level: 1 - low speed, 2 - medium
speed or 3 - high speed. To do so, press the
corresponding buttons and then release
them.
3. LAMP SWITCH-ON To switch the lamp on,
press the button located at the top left and
then release it.
4. LAMP SWITCH-OFF To switch the lamp
off, press the button located at the top right
and then release it.
Precautions
- Be careful with the remote control: avoid bumps or falls.
- The batteries should not be exposed to excessive heat such
as sunlight, fire or similar.
- If the unit is not going to be used for a long period of time,
remove the batteries from their compartment.
Содержание COSMO 1252421
