ECR International Dunkirk DCB-100 Скачать руководство пользователя страница 18

Страница: 18 / 143

4 - LOCATING BOILER

4.1 Boiler Location Considerations

• Ambient room temperature always above 32°F (0°C) to

prevent freezing of liquid condensate.

• Approved for installation in closets or alcove provided

it is correctly designed for that purpose and minimum

clearances are met.

• Protect gas ignition system components from water

(dripping, spraying, rain, etc.) during operation and

service (circulator replacement, condensate trap,

control replacement, etc.).

• Access to outdoors to meet minimum and maximum

pipe lengths for combustion air and vent piping. See

section 5.

• Disposal of condensate. See section 5.
• Drainage of water (or water - antifreeze solution)

during boiler service or from safety relief valve

discharge. See section 6.

• Access to system water piping, gas supply, and

electrical service. See sections 6, 7 and 8

• Clearances to combustible materials and service

clearances.

See Table 1 and Figures pg. 15.

•

Boiler shall be installed on flat vertical wall which is

capable of supporting the weight of the boiler.

• Room-sealed boiler installed in a room containing bath

or shower shall be installed so person using bath or

shower cannot touch any electrical switch or boiler

control utilizing line voltage electricity.

• Multiple Boilers can be wall mounted, placed side by

side, or back to back.

• Observe service clearances in all installations.
• For Direct Vent installations, air vents are not required

in room boiler is installed in, or when installed in closet

or compartment.

• Requires fresh air intake piped from outdoors, do not

install where air inlet is dusty or dirty.

•

Install a filter on the air intake if boiler is installed in

dusty or dirty enviroment. A high flow air filter with

minimum air filtratrion of 800 cfm can be placed on the

air intake section of the vent pipe. Boiler performance

at maximum vent length may be impacted when an air

filter is used.

• Use of unregulated gas (well gas) is not manufacturer

recomended with this boiler.

TABLE 1: BOILER CLEARANCES

Dimension

Combustible

Materials

(1)

Manufacturer

Recommended

for Service

(1)(2)

Top

0" (0 cm)

8-5/8" (220 mm)

Left Side

1-3/4" (45 mm)

Right Side

1-3/4" (45 mm)

Front

0" (0 mm)

17-3/4"(450 mm)

Back

0" (0 mm)

Bottom

0" (0 mm)

*9-13/16"

(250 mm)

Combustion Air/

Vent piping

0" (0 mm)

6" (160 mm)

(1)

Required distances measured from boiler jacket.

(2)

Service, proper operation clearance recommendation.

* Allowance for piping at the bottom of boiler not included.

WARNING

Fire Hazard! Do not install on carpeting. Failure to

follow these instructions could result in death or

serious injury.

NOTE: Greater clearances for access should supersede fire

protection clearances.

240013501 REV A [03/15/2022]

Содержание Dunkirk DCB-100
















































































































































Результаты поиска

Содержание Dunkirk DCB-100

Отзывы:

Бренды по названию

Популярные бренды

ECR International Dunkirk DCB-100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk DCB-100

Отзывы:

Бренды по названию

Популярные бренды