Eclipse EC-P8, Руководство по установке

Страница: 29 / 48

P0031-LI-02.01 29
No Type & Description
0010 Confirmed Alarm
This output type activates when two different zones cause
an intruder alarm.
0011 Alarm Abort
This output type activates when the user disarms the system
after an alarm and within the “Abort Delay” period.
0012 Fire Alarm
This output type activates when a fire alarm is generated.
0013 PA Alarm
This output type activates when a panic alarm is generated.
0014 Duress Alarm
This output type activates when a duress alarm is generated.
0015 24hr Alarm
This output type activates when a 24hr alarm is generated.
0016 Medical Alarm
This output type activates when a medical alarm is
generated.
0017 Tamper Alarm
This output type activates when a tamper alarm is
generated.
0018 Ready
This output type activates when the system is ready for
arming, i.e. all zones are healthy.
0019 Trouble
This output type activates when a trouble alarm is
generated.
0020 Alert
This output type activates when an alert event is generated
and deactivates when the user has acknowledged the alert.
0021 Zone Bypass
This output type activates when one or more zones are
bypassed.
0022 In Walk Test
This output type activates when the user walk test mode is
selected.
0023 Flash 1 Second
This output type continually pulses on and off at a rate of 1
second.
0024 User Test Active
This output type activates when the user test mode is
selected in the “Bell Test” menu.
0025 PSTN Fault
This output type activates when a fault is detected on the
PSTN connected to the control panel.
0026 PSTN Off Hook
This output type activates when an off-hook condition is
detected on the PSTN connected to the control panel.
0027 PSTN Ringing
This output type activates when ringing is detected on the
PSTN connected to the control panel.
0028 Battery Fault
This output type activates when a fault is detected with the
control panel standby battery.
0029 Box Tamper Fault
This output type activates when the control panel box
tamper is open.
0030 Bell Tamper Fault
This output type activates when the control panel bell
tamper is open.
0031 Engineer on Site
This output type activates when the engineer is logged on.
0032 Detector Reset
This output type is normally active and is used for powering
devices that require their power supply to be removed in
order to reset them. The output deactivates for 5 seconds at
the start of exit mode and when the system is reset.
No Type & Description
0033 Detector Latch
This output type is used to latch the alarm condition on
detection devices that have a latch input.
0034 System Low Volts
This output type activates when a low voltage fault is
detected with the control panel standby battery.
0035 In Exit
This output type activates when the system is in exit mode.
0036 In Entry
This output type activates when the system is in entry mode.
0037 In Second Entry
This output type activates when the system is in second
entry mode.
0038 In Alarm
This output type activates when any alarm is generated.
0039 Auxiliary Alarm
This output type activates when an auxiliary alarm is
generated.
0040 Warning Alarm
This output type activates when a warning alarm is
generated.
0041 Keypads Locked
This output type activates when a security key is active.
0042 Output Fault
This output type activates when a fault is detected on one of
the monitored control panel outputs.
0043 Call Engineer
This output type activates when the system requires an
engineer access code in order to reset the system.
0044 Device Fault
This output type activates when a device fault is detected.
0045 Service Required
This output type activates when the service timer expires.
0046 Cleaner Bypassed
This output type activates when a “Cleaner Bypass” is
invoked.
0047 N/A
Not available on the EC-P8.
0048 N/A
Not available on the EC-P8.
0049 N/A
Not available on the EC-P8.
0050 Door Access
This output type activates for 30 seconds when any valid
user code is entered.
0051 Alarm Test
This output type activates when the user select the alarm
sounder test.
0052 Panel AC On
This output type activates when the mains supply is present.
Group 02: Control Timer
The EC-P8 has 5 control timers each timer can be assigned to an
output:
No Type & Description
0201 Control Timer 1
This output type activates when Control Timer 1 is on and
deactivates when Control Timer 1 is off.
0202-
0205 Control Timer 2 - 5
As Control Timer 1.