Eclipse EC-P8, Руководство по установке

Страница: 21 / 48

P0031-LI-02.01 21
2. Arming Control
This section covers programming of the arming modes, timers
and options that control the way the system is armed.
Arming Timers
Each arming mode has its own set of timers that are used to
control various delays during arming, disarming and in alarm.
Locations:
2001
to
2007
Away Arm: Timers 01 to 07.
2101
to
2107
Stay Arm 1: Timers 01 to 07.
2201
to
2207
Stay Arm 2: Timers 01 to 07.
2301
to
2307
Stay Arm 3: Timers 01 to 07.
Entry Mode: Number Entry (see page 17).
01 Exit Delay
When the Arming Mode is configured as Timed or deferred, this
timer sets the delay between the user initiating the exit procedure
and the system actually arming.
02 Entry 1 Delay
When the system is armed, activation of a “Final Exit 1” zone will
start the entry 1 delay timer, this allows the user time to access
the remote keypad and disarm the system.
03 Entry 2 Delay
When the system is armed, activation of a “Final Exit 2” zone will
start the entry 2 delay timer, this allows the user time to access
the remote keypad and disarm the system.
04 Second Entry
If at the end of normal entry (Entry 1 or 2) delay, the system has
not been disarmed, the system will start the second entry delay,
during this time the internal alarm tone will sound. If at the end of
the second entry delay the system has still not been disarmed, a
full alarm is generated.
05 Bell Delay
When an alarm is generated, this timer is used to delay the
activation of the external sounder and strobe.
06 Bell Duration
When an alarm is generated, this timer is used to control the
active duration of the external sounder and strobe.
07 Comms Delay
When an alarm is generated, this timer is used to delay the
activation of the on-board communicator.
Arming Modes
This set of options control how the system is armed for each
arming mode.
Locations:
2031
- Away Arm: Arming Mode.
2131
- Stay Arm 1: Arming Mode.
2231
- Stay Arm 2: Arming Mode.
2331
- Stay Arm 3: Arming Mode.
Entry Mode: Bit Toggle Selection (see page 16).
0 Final Exit
When the exit mode is started, the system will only arm after the
activation of a Final Exit 1 or Final Exit 2 zone type, e.g., after the
front door is opened the closed.
1 Timed Exit
When the exit mode is started, the system will arm after the Exit
Delay timer has expired.
2 Exit Terminator
When the exit mode is started, the system will only arm after
activation of a Final Exit 1 or Final Exit 2 zone type, followed by
the activation of an Exit terminator zone, e.g., after the front door
is opened the closed and the push to set button has been
pressed.
3 Deferred
When the exit mode is started, the system will arm after the Exit
Delay timer has expired. However, if a zone off the exit route is
activated during this period, the Exit Delay timer is suspended
whilst the zone is active.
Arm Options 1
The set of options controls how the system responds for each
arming mode.
Locations:
2041
- Away Arm: Options 1.
2141
- Stay Arm 1: Options 1.
2241
- Stay Arm 2: Options 1.
2341
- Stay Arm 3: Options 1.
Entry Mode: Bit Toggle Selection (see page 16).
1 Arming with AC off
On: The system can be armed when the mains supply is
switched off.
Off: The system cannot be armed when the mains supply is
switched off.
2 Arming with ATS Fault
On: The system can be armed with an Alarm Transmission Fault
(telephone line fault).
Off: The system cannot be armed when the mains supply is
switched off.
3 Auto Stay Arm 1
On: The system automatically performs a Stay Arm 1, if the user
does not activate a Final Exit zone.
Off: The system will always perform an Away Arm.
4 Silent Exit
On: The exit tone remains silent during exit mode.
Off: The exit tone is generated during exit mode.
5 Local Exit Tone
On: If the exit tone is enabled, the exit tone is only generated
from the remote keypad that was used arm the system.
Off: If the exit tone is enabled, the exit tone is generated from all
devices.
6 Anti-Masking when Armed
On: Anti-Masking faults are only monitored when the system is
armed.
Off: Anti-Masking faults are monitored at all times.
7 Bell on Arm Fail
On: If the system fails to arm, the external sounder and strobe is
activated.
Off: The external sounder and strobe are not activated.
8 Pulse Strobe on Arm
On: When the system is armed successfully, the external strobe
is activated for 5 seconds.
Off: The external strobe is not activated.