Echo SRM-410X страница 46 Скачать руководство пользователя

Страница: 46 / 56

MAINTENANCE

SRM-410X

X7502168400

Sharpening Metal Blades

Several styles of metal blades are

approved for use on the

Brushcutter. The 8-tooth blade can

be sharpened during normal

maintenance. The clearing blade

and 80-tooth blade require

professional service.

Before sharpening, CLOSELY

inspect blade for cracks (look at the

bottom of each tooth and the center

mounting hole closely), missing

teeth and bending. If ANY of these

problems are discovered, replace

the blade.

When sharpening a blade, always remove the same amount of materials

from each tooth to maintain balance. A blade that is not balanced will cause

unsafe handling due to vibration and can result in blade failure.

File each tooth at a 30° angle a

specific number of times, e.g.,

four strokes per tooth. Work

your way around the blade until

all teeth are sharp.

DO NOT file the ‘gullet’ (radius)

of the tooth with the flat file. The

radius must remain. A sharp

corner will lead to a crack and

blade failure.

If an electric grinder is used, use care not to overheat teeth, do not
allow tips/tooth to glow red or turn blue. DO NOT place blade in
cooling water. This will change the temper of the blade and could
result in blade failure.

30º

Содержание SRM-410X

























































Результаты поиска

Содержание SRM-410X

Отзывы:

Похожие инструкции для SRM-410X

Бренды по названию

Популярные бренды

Echo SRM-410X, Руководство оператора

Результаты поиска

Содержание SRM-410X

Отзывы:

Похожие инструкции для SRM-410X

Бренды по названию

Популярные бренды