Echo SRM-410X страница 11 Скачать руководство пользователя

Страница: 11 / 56

SRM-410X

SAFETY

X7502168400

Do not operate this product indoors or in inadequately
ventilated areas. Engine exhaust contains poisonous emissions
and can cause serious injury or death.

Read Manuals

• Provide all users of this equipment with literature for instructions on safe

operation.

Clear The Work Area

• Always clear the work area of foreign objects such as rocks, broken

glass, nails, wire, or string,, and check for any hidden hazards. Spectators

and fellow workers must be warned, and children and animals prevented

from coming nearer than 50 ft. (15 m) while the unit is in use.

• Outside the 15 m (50 ft) zone, there is still a risk of injury from thrown

objects.

• Bystanders should be encouraged to wear eye protection.

• If you are approached, stop the engine and cutting attachment.

• When a bladed unit is used, there is the added risk of injury to bystanders

being struck with the moving blade in the event of a blade thrust or other

unexpected reaction of the blade.

Keep A Firm Grip

• Always hold throttle handle and support handle with thumbs and fingers

tightly encircling the handles.

Keep A Solid Stance

• Maintain footing and balance at all times. Do not stand on slippery,

uneven or unstable surfaces. Do not work in odd positions or on ladders.

Do not over reach.

• Keep cutting attachment below waist.

• Keep all body parts away from rotating cutting attachment.

Avoid Hot Surfaces

• Keep exhaust area clear of flammable debris. Avoid

contact during and immediately after operation.

Содержание SRM-410X

























































Результаты поиска

Содержание SRM-410X

Отзывы:

Похожие инструкции для SRM-410X

Бренды по названию

Популярные бренды

Echo SRM-410X, Руководство оператора

Результаты поиска

Содержание SRM-410X

Отзывы:

Похожие инструкции для SRM-410X

Бренды по названию

Популярные бренды