Echo SRM-410X страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 56

background image

SRM-410X

MAINTENANCE

X7502168400

37

© 11/20 ECHO Incorporated

1.

Close choke (COLD START

position). This prevents dirt

from entering the carburetor

throat when the air filter is

removed. Brush accumulated

dirt from air cleaner area.

2.

Remove air filter cover (A).

Brush dirt from inside cover.

3.

Remove air filter (B) from case.

Use care to prevent dirt and

debris from falling into case.

4.

Inspect filter element and seal.

Replace filter if any of these

problems are present:
• Air filter seal does not fit tightly against case
• Air filter seal is distorted, worn, or damaged
• Air filter element has holes or other damage
• Air filter element is saturated with dirt
• Air filter element is soaked with fuel mix

5.

If air filter is in good condition and can be cleaned and reused, lightly

brush debris from air filter element, or blow filter element clean using

low pressure (40 psi or less) compressed air directed at inside of filter.

When using compressed air, always direct air stream at inside
surface of filter so dust and debris will be blown out of filter. Keep air
nozzle 6 - 8 inches away from filter to prevent damage to filter.

6.

Install air filter in case, and replace cover.

Fuel Filter

Level 1.

Parts Required: Tune Up Kit.

A

B

«
...
35
36
37
38
39
...
»

Содержание SRM-410X

























































Отзывы:

Нет отзывов

Похожие инструкции для SRM-410X

Бренд: SaMASZ Страницы: 24

Бренд: Ironside Страницы: 44

Бренд: Echo Страницы: 36

Бренд: Hyundai Страницы: 16

Бренд: Yard force Страницы: 14

Бренд: Patriot Страницы: 28

Бренд: Echo Страницы: 176

Бренд: Virutex Страницы: 36

Бренд: PrimAster Страницы: 24

OneBlade EFM-2120OB

Бренд: euroo Страницы: 6

CH 22 EBP2 (62ST)

Бренд: Hitachi Koki Страницы: 24

Бренд: Sun Lawn Страницы: 16

Бренд: Sun joe Страницы: 10

Бренд: Draper Страницы: 12

Бренд: Westfalia Страницы: 44

Бренд: GreenWorks Pro Страницы: 191

Бренд: Haussmann Страницы: 16

Бренд: 909 Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды