Echo SRM-410X Скачать руководство пользователя страница 8

Страница: 8 / 56

SAFETY

SRM-410X

X7502168400

Eye Protection

◆

Eye protection that meets ANSI Z87.1 or CE requirements
must be worn whenever you operate the unit.

◆

For additional safety, a full-face shield can be worn over
safety glasses or goggles to provide protection from sharp
branches or flying debris.

Hand Protection

Wear sturdy, no-slip, rubber work gloves to improve your grip on the

handles. Gloves also provide protection against cuts and scratches, cold

environments, and reduce the transmission of machine vibration to your

hands.

Hearing/Ear Protection

ECHO recommends wearing personal protective equipment whenever unit

is used.

Breathing Protection

Operators who are sensitive to dust or other common airborne allergens

may need to wear a dust mask to prevent inhaling these materials while

operating unit. Dust masks can provide protection against dust, plant debris,

and other plant matter such as pollen. Make sure the mask does not impair

your vision, and replace the mask as needed to prevent air restrictions.

Proper Clothing

Wear snug-fitting, durable clothing:

• Pants should have long legs, shirts should have long sleeves.

• DO NOT WEAR SHORTS.

• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or

hanging items that could become entangled in moving parts or

surrounding growth.

• Keep clothing buttoned or zipped, and keep shirt tails tucked in.

• Wear sturdy work shoes with nonskid rubber soles.

• DO NOT WEAR OPEN TOED SHOES.

• DO NOT OPERATE UNIT WITH BARE FEET.

Keep long hair away from engine and air intake. Retain hair with cap or net.

Содержание SRM-410X

























































Результаты поиска

Содержание SRM-410X

Отзывы:

Echo SRM-410X, Руководство оператора, Страница: 8 / 56

Результаты поиска

Содержание SRM-410X

Отзывы: