Echo SRM-410X страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 56

background image

OPERATION

SRM-410X

22

X7502168400

© 11/20 ECHO Incorporated

• For barrier bar or u-handle, follow instructions supplied with either blade

conversion kit or U-handle kit, and verify blade is secured properly.

• A new cotter pin is required each time a blade is installed.

• Shoulder harnesses may be used on all trimmers and brushcutters to

reduce operator fatigue. Brushcutters over 7.5 kg (16.5 lbs.) dry weight

(without fuel) and u- handle brushcutters REQUIRE a double shoulder

harness.

Note: The barrier bar is used to restrict rearward movement

of the unit. The barrier bar is not a handle and should
not be gripped when using or carrying the unit.

Blade Selection

The type of blade used MUST be matched to the type and size of
material cut. An improper or dull blade can cause serious
personal injury. Blades MUST be sharp. Dull blades increase the
chance of kick-out and injury to yourself and bystanders. Never
use an edging blade, circular saw blade, or any other type of
unapproved blade.

3-Tooth Grass/Weed Blades

may be used wherever the nylon line head is

used. DO NOT use this blade for heavy weeds or brush.

8 Tooth Weed/Grass Blade

is designed for grass, garden debris and thick

weeds up to 19 mm (0.75 in.) diameter. DO NOT use this blade for brush or

heavy woody growth.

80 Tooth Brush Blade

is designed for cutting brush and woody growth up

to 13 mm (0.5 in.) diameter.

22 Tooth Clearing Blade

is designed for dense thickets and saplings up to

64 mm (2.5 in.) diameter.

A trimmer-brushcutter with a metal blade can cause serious
injuries if handled improperly.

«
...
20
21
22
23
24
...
»

Содержание SRM-410X

























































Отзывы:

Нет отзывов

Похожие инструкции для SRM-410X

Бренд: GreenWorks Страницы: 28

Бренд: Oleo-Mac Страницы: 76

Бренд: Nakayama Страницы: 26

Бренд: AEG Страницы: 16

Бренд: Ryobi Страницы: 104

Бренд: EINHELL Expert Страницы: 16

Бренд: McCulloch Страницы: 2

Бренд: King Canada Страницы: 3

EURODIM TWIN TECH

Бренд: ADB Страницы: 96

Бренд: EarthWise Страницы: 30

Бренд: bannerman Страницы: 20

Бренд: Parklander Страницы: 21

Бренд: Parkside Страницы: 80

ZS 2620 Magnetic

Бренд: ECG Страницы: 128

GT-200R - 07-07

Бренд: Echo Страницы: 24

Бренд: Makita Страницы: 13

Бренд: Makita Страницы: 128

Бренд: Makita Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды