Echo SRM-225 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 52

Echo SRM-225 Скачать руководство пользователя страница 16

DESCRIPTION

SRM-225

16

X7722279402

© 2/2016 ECHO Inc.

14.

SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER
WITH CATALYST

-The muffler or catalytic muffler controls exhaust noise

and emission. The spark arrestor screen prevents hot, glowing particles of
carbon from leaving the muffler. Keep exhaust area clear of flammable
debris.

15.

FUEL TANK

- Contains fuel and fuel filter.

16.

FUEL TANK CAP

- Covers and seals fuel tank opening.

17.

CHOKE

- The choke control is located at the rear of the air cleaner

housing. Move choke lever to COLD START (

) to close choke for cold

start. Move choke lever to “RUN” (

) position to open choke.

18.

AIR CLEANER

- Contains replaceable filter element.

19.

PURGE BULB

- Pumping purge bulb before starting engine draws fresh

fuel from the fuel tank, purging air from the carburetor. Pump purge bulb
until fuel is visible and flows freely in the clear fuel tank return line. Pump
purge bulb an additional 4 or 5 times.

«
...
14
15
16
17
18
...
»

Содержание SRM-225





















































Отзывы:

Нет отзывов