manualshive.com logo in svg

Echo CGSL01AF1, Руководство оператора

Поделиться
Скачать
Echo CGSL01AF1 Скачать руководство пользователя страница 23

20

P

OWER

 S

WITCH

C

HAPTER

 9

O

PERATION

9. Operation

9.1. Power Switch

The power switch is located under dust cover.

Move the power switch to the ON position to energize the DC output of the charging station and the 
peripheral wires. The TEST LED will not illuminate.

Move the power switch to the OFF position to de

‐

energize the DC output of the charging station and the 

peripheral wires.

Move the power switch to the TEST position to energize the DC output of the charging station and the 
peripheral wire(s). The TEST LED will illuminate.

9.2. LED Indicators

Four LED indicators are located on the input panel (rear side of charger).

WARNING

: 

If an LED is not illuminated, AC power may still be present.

TEST LED 

‐

 Illuminates green when AC power is present and the power switch is in the TEST position.

SL (Station Loop) LED 

‐

 Blinks green when the station loop peripheral wire is correctly connected, blinks 

red when incorrectly connected.

Z1 (Field Zone 1) LED 

‐

 Blinks green when Field Zone 1 peripheral wire is correctly connected, blinks red 

when incorrectly connected.

1 

‐

 Power switch

3 

‐

 ON position

1A 

‐

 Power switch (side view)

4 

‐

 OFF position

2 

‐

 Dust cover

5 

‐

 TEST position

2

1

3

4

5

1A

Содержание CGSL01AF1







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды