manualshive.com logo in svg

Echo CGSL01AF1, Руководство оператора

Поделиться
Скачать
Echo CGSL01AF1 Скачать руководство пользователя страница 11

8

R

EQUIRED

 T

OOLS

C

HAPTER

 6

C

HARGING

 S

TATION

 I

NSTALLATION

 R

EQUIREMENTS

6. Charging Station Installation Requirements

Identify the location of AC power, Station Loop, Field Zone 1, and Field Zone 2 peripheral wires before 
installing the charging station. Install the charging station on flat ground where flooding or water accu

‐

mulation will not occur. Do not bend, warp, or crack the base during installation.

6.1. Required Tools

6.2. AC Power Supply Wiring

Use 14 AWG electrical wire and ½ in. liquid

‐

tight electrical conduit for AC power into the charging station.

NOTE

: 

Wire and conduit are not included with the charging station.

8 mm Socket Driver

Hammer

3 mm Flat

‐

Blade Screwdriver

Slip

‐

Joint Pliers

#1 Phillips Screwdriver

T

‐

27 Torx® Driver

Adjustable Wrench

7/8 in. Drill Bit

Wire Strippers

Fasteners and additional cord grip for Timer Box 
Accessory Kit (not included)

Tape Measure

1 

‐

 Line (black)

3 

‐

 Neutral (white)

2 

‐

 Ground (green)

4 

‐

 Liquid

‐

tight electrical conduit

1

1

1

2

1

3

4

Содержание CGSL01AF1







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды