Echo Bear Cat SC3306 Скачать руководство пользователя страница 2

Страница: 2 / 32

Before You Begin

DEAR ECHO Bear Cat

CUSTOMER

Thank you for purchasing an ECHO Bear Cat product. The ECHO Bear Cat line is designed, tested, and manufactured

to give years of dependable performance. To keep your machine operating at peak efficiency, it is necessary to adjust

it correctly and make regular inspections. The following pages will assist you in the operation and maintenance of your

machine. Please read and understand this manual before operating your machine.
If you have any questions or comments about this manual, please call us toll-free at 888.625.4520.
If you have any questions or problems with your machine, please call or write your local authorized ECHO Bear Cat

dealer.
This document is based on information available at the time of its publication. ECHO Bear Cat is continually making

improvements and developing new equipment. In doing so, we reserve the right to make changes or add improvements

to our product without obligation for equipment previously sold.

PLEASE SEND US YOUR WARRANTY CARD

A warranty card is included in your owner’s kit packaged with your machine. Please take the time to fill in the information

requested on the card. When you send your completed card to us, we will register your machine and start your coverage

under our limited warranty or go to bearcatproducts.com/Product-Support/Product-Registration.

FOR MACHINE SERVICE OR PARTS

For service assistance, contact your nearest authorized

ECHO Bear Cat dealer or the factory. For parts, contact

your authorized dealer. The parts manual for your

machine is available at bearcatproducts.com/Product-

Support/Find-A-Product-Manual. Your dealer will need to

know the identification number of your machine to provide

the most efficient service. See below for information on

how to identify and record the identification number for

your machine.

FOR ENGINE SERVICE OR PARTS

For engine service or parts, contact your nearest

authorized engine dealer. ECHO Bear Cat does not

handle any parts, repairs or warranties for engines.

ORDERING PARTS

Only genuine ECHO Bear Cat replacement parts should

be used to repair the machine. Replacement parts

manufactured by others could present safety hazards,

even though they may fit on this machine. Replacement

parts are available from your ECHO Bear Cat dealer.

Provide the following when ordering parts:

The SERIAL NUMBER or VIN of your machine.
The PART NUMBER of the part.
The PART DESCRIPTION.
The QUANTITY needed.

HOW TO CONTACT ECHO Bear Cat

ADDRESS

PHONE

E-MAIL

HOURS

237 NW 12th Street

P.O. Box 849

West Fargo, ND 58078

888.625.4520

701.282.5520

Fax: 701.282.9522

[email protected]

Monday - Friday

8 a.m. to 5 p.m.

Central Time

IDENTIFICATION NUMBER LOCATION

Your machine will have a serial number. Serial numbers

are located on the machine body. They are 6-digit

numbers. For the exact location of the serial number,

see the parts manual available at bearcatproducts.com/

Product-Support/Find-A-Product-Manual.

Record your identification number in the space provided

and on the warranty registration card.

SERIAL NUMBER

MANUFACTURED BY CRARY INDUSTRIES

MANUFACTURED IN U.S.A.

XXXXXX

WEST FARGO, NORTH DAKOTA 58078 U.S.A.

SERIAL NUMBER

Содержание Bear Cat SC3306

































Результаты поиска

Содержание Bear Cat SC3306

Отзывы:

Похожие инструкции для Bear Cat SC3306

Бренды по названию

Популярные бренды

Echo Bear Cat SC3306, Руководство пользователя

Результаты поиска

Содержание Bear Cat SC3306

Отзывы:

Похожие инструкции для Bear Cat SC3306

Бренды по названию

Популярные бренды