Echo Bear Cat SC3306 Скачать руководство пользователя

Страница: 6 / 32

3 INCH CHIPPER/SHREDDER

SAFETY

1. Always stand clear of discharge area when operating

this machine. Keep face and body away from feed

and discharge openings.

2. Keep hands and feet out of feed and discharge

openings while machine is operating to avoid serious

personal injury. Stop and allow

machine to come to a complete

stop before clearing obstructions.

3. Set up your work site so you are

not endangering traffic and the

public. Take great care to provide

adequate warnings.

4. Do not climb on machine when operating. Keep

proper balance and footing at all times.

5. Check cutting chamber to verify it is empty before

starting the machine.

6. The rotor will continue to rotate after being disengaged.

Shut off the machine and make sure all moving parts

have come to a complete stop before inspecting or

servicing any part of the machine. Disconnect the

battery and remove the ignition key if applicable.

7. Do not insert branches with a diameter larger than

the max chipper capacity into machine or machine

damage may occur.

8. When feeding material into machine, do not allow

metal, rocks, bottles, cans or any other foreign

material to be fed into the machine.

13. Do not operate machine without shields in place.

Failure to do so may cause serious injury or death.

14.

Keep all guards, deflectors, and shields in good

working condition.

15. Before inspecting or servicing any part of this machine,

shut off the machine and make sure all moving parts

have come to a complete stop. Disconnect the battery

and remove the ignition key where applicable.

16. Check that all screws, nuts, bolts, and other fasteners

are secured, tightened and in proper working condition

before starting the machine.

17. Do not transport or move machine while it is operating

or running.

1.3 BEFORE OPERATING

1. Read and understand this owner’s manual. Be

completely familiar with the controls and the proper

use of this equipment.

2. Familiarize yourself with all of the safety and

operating decals on this equipment and on any of its

attachments or accessories.

3. Keep safety decals clean and legible. Replace

missing or illegible safety decals.

4. Obtain and wear safety glasses

and use hearing protection at all

times when operating this machine.

Avoid wearing loose fitted clothing.

Never operate this machine while

wearing clothing with drawstrings that could wrap

around or get caught in the machine.

6. Do not operate this machine if you are under the

influence of alcohol, medications, or substances that

can affect your vision, balance or judgement. Do not

operate if tired or ill. You must be in good health to

operate this machine safely.

7. Do not operate this equipment in the vicinity of

bystanders. Keep the area of operation clear of all

persons, particularly small children. It is recommended

that bystanders keep at least 50 feet (15 meters)

away from the area of operation.

8. Do not allow children to operate this equipment.
9.

Use only in daylight or good artificial light.

10. Do not run this equipment in an enclosed area. Engine

exhaust contains carbon monoxide gas, a deadly

poison that is odorless, colorless and tasteless.

Do not operate this equipment in or near buildings,

windows or air conditioners.

11. Always use an approved fuel container. Do not

remove gas cap or add fuel when engine is running.

Add fuel to a cool engine only.

12.

Do not fill fuel tank indoors. Keep open flames, sparks,

smoking materials and other sources of combustion

away from fuel.

1.4 OPERATION SAFETY

Содержание Bear Cat SC3306

































Результаты поиска

Содержание Bear Cat SC3306

Отзывы:

Похожие инструкции для Bear Cat SC3306

Бренды по названию

Популярные бренды

Echo Bear Cat SC3306, Руководство пользователя

Результаты поиска

Содержание Bear Cat SC3306

Отзывы:

Похожие инструкции для Bear Cat SC3306

Бренды по названию

Популярные бренды