Echo Bear Cat SC3306 Скачать руководство пользователя страница 8

Страница: 8 / 32

3 INCH CHIPPER/SHREDDER

SAFETY

1.7 SAFETY DECALS

Do not operate machine without shields in place.

Failure to do so may cause serious injury or death.

Keep hands and feet out of inlet and

discharge openings while machine is

operating to avoid serious personal injury.

Stop and allow machine to come to a complete stop before clearing

obstructions.

Do not insert branches larger than 3/4

inch into shredder or machine damage

may occur.

Do not insert branches larger than 3 inches in diameter into chipper.

Machine damage may occur. Refer to owners manual for operating

instructions and recommendations.
Keep hands and feet out of inlet and discharge openings while machine

is operating to avoid serious personal injury. Stop and allow machine to

come to a complete stop before clearing obstructions.

Read and understand you owners manual before operating. If owners

manual was not included or you have any questions, please call

800.247.7335 or 701.282.5520

(U.S.A.).
Do not operate this equipment

in the vicinity of bystanders. Do

not allow children to operate this

equipment. Obtain and wear

safety glasses and use hearing

protection at all times when

operating this machine. Before

inspecting or servicing any part

of this machine, shut off power

source, disconnect spark plug

wire from spark plug and make

sure all moving parts have come

to a complete stop. Always stand

clear of discharge area when

operating this machine. Keep

face and body away from feed

and discharge openings. When

feeding shreddable material

into chipper, do not allow metal,

rocks, bottles, cans or any other

foreign material to be fed into

chipper or shredder. Before

inspecting or servicing any part

of this machine, shut off power

source, disconnect spark plug

wire from spark plug and make

sure all moving parts have come

to a complete stop.
Check blade bolts for proper

torque after every 8 hours of

operation. Check blades and

rotate or resharpen daily or as

required to keep blades sharp.

Refer to owners manual for

instructions. Failure to do so

may cause poor performance,

damage or personal injury and

will void the machine warranty.
Lower lever slowly to engage

chipper. Pull lever up to

disengage chipper. Chipper/

shredder rotor will continue

to rotate when clutch is disengaged. Stop engine and remove spark

plug wire before cleaning debris from discharge area or servicing this

machine. Do not operate without discharge screen, inlet flaps and all

shields in place.

See Section 1.8 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine

and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety

instructions and decals.

PN 12174

PN 12175

PN 12176

PN 31989-00

PN 31990-00

Operation of this equipment may create

sparks that can start fires around dry

vegetation. A spark arrestor may be

required. The operator should contact local

fire agencies for laws or regulations relating

to fire prevention requirements.

PN 33883-00

33883-00

WARNING

ADVERTENCIA

OPERATION OF THIS EQUIPMENT MAY CREATE SPARKS

THAT CAN START FIRES AROUND DRY VEGETATION. A

SPARK ARRESTOR MAY BE REQUIRED. THE OPERATOR

SHOULD CONTACT LOCAL FIRE AGENCIES FOR LAWS

OR REGULATIONS RELATING TO FIRE PREVENTION

REQUIREMENTS.

EL USO DE ESTE EQUIPO PUEDE CREAR CHISPAS

CAPACES DE INICIAR INCENDIOS EN VEGETACION

SECA. PODRIA SE NECESARIO USAR UN PARACHISPAS.

EL OPERADOR DEBERA COMUNICARSE CON CUERPOS

DE BOMBEROS LOCALES PARA INFORMARSE DE LEYES

O REGLAMENTOS RELACIONADOS CON LOS

REQUISITOS EXIGIDOS PARA LA PREVENCION DE

INCENDIOS.

Содержание Bear Cat SC3306

































Результаты поиска

Содержание Bear Cat SC3306

Отзывы:

Похожие инструкции для Bear Cat SC3306

Бренды по названию

Популярные бренды

Echo Bear Cat SC3306, Руководство пользователя

Результаты поиска

Содержание Bear Cat SC3306

Отзывы:

Похожие инструкции для Bear Cat SC3306

Бренды по названию

Популярные бренды