Eaton MTL F809F-Plus Скачать руководство пользователя

Страница: 7 / 64

Eaton’s Crouse-Hinds Business
Cooper Crouse-Hinds Pte Ltd
No. 2 Serangoon North Ave 5 #06-01
Singapore 554911

tel: + 65 6645 9888
fax: +65 6297 4819

Page 7

5.1.

5.1.1.

Introduction

This is the main option for viewing both segment and device characteristics collected by the

MTL F809F diagnostic module. Choose the data you want displayed by clicking on a specific

node in the Navigation Area on the left of the screen.

5.1.2.

Online / Offline view

View data in Online or Offline mode. In online mode, it will repeatedly refresh the parameters

displayed on the current page to present current values, the status of any alerts and

limitations. In offline mode, it just shows the parameter values, alert status and limits last

stored in DTM locally.

You may select online and offline mode from the DTM menu.

The refresh rate for the online mode can be configured in an XML file stored on the system.

It can be found inside the installed application folder at the following location

"...\XML\DtmSettings.xml";. Search within this file for the "TimeInterval" parameter:

Содержание MTL F809F-Plus

































































Результаты поиска

Содержание MTL F809F-Plus

Отзывы:

Похожие инструкции для MTL F809F-Plus

Бренды по названию

Популярные бренды

Eaton MTL F809F-Plus, Руководство пользователя

Результаты поиска

Содержание MTL F809F-Plus

Отзывы:

Похожие инструкции для MTL F809F-Plus

Бренды по названию

Популярные бренды