Eaton MPCV Series Скачать руководство пользователя

Страница: 15 / 32

Instruction Booklet

IB02402001E

December 2010

Instructions for the Eaton Type

MPCV Network Protection Relay

EaToN CoRPoRaTIoN www.eaton.com

IB02402001E

For more information visit: www.EatonElectrical.com

Instruction Bulletin

Effective: September 2004

Page

Instruction for the

Cutler-Hammer Type MPCV

Network Protection Relay

Characteristic Line

Straight Line (Standard) — Used on typical loaded system.

Circular — Used on lightly loaded system.

Pump Protection

This feature shall protect the network protector from exces-

sive close-trip (pumping) operation within a given time. When

the protector number of operations is equal or greater than

the breaker cycles within the pump time setting, the relay

shall initiate a trip and lock open to inhibit a close

operation until the reset time expires.

Manual (Remote) Close

Initiated via PowerNet by a PRC (Protective Remote Close)

command. The relay will relax the close criteria by effectively

setting the ML to near zero volts and expand the phasing

line(s) to the setpoint boundary for up to 10 seconds or until

closure is initiated. Upon expiration of the 10-second PRC

window or closure initiation, the original ML and PL pro-

grammed settings are restored. The Anti-Pump Protection

must be off to complete the PRC operation.

Dead Network

The relay shall initiate an instantaneous closure when the net-

work voltage is equal or less than the Dead Network setting.

Communication

Medium

INCOM with 1500 volt isolation via 3-pin connector and a

twisted pair cable.

Standard pendant via DB9 connector.

Protocol

INCOM — a Master/Slave two-way communication system.

The master (PC that has an RS-232c communication port)

requires the use of a MINT (Master INCOM Network Translator)

to convert the 33-bit binary messages to and from a 10 byte

ASC

encoded hexadecimal RS-232c messages.

Modulation: Carrier Based, FSK

Frequency: 115.2 KHz logical “one”, 92.16 KHz logical “zero”.

■

Message: 33 bits.

■

Start Bit: 2 bits.

■

Control Bit: 1 bit.

■

Data: 24 bits.

■

BHC Check: 5 bits code.

Safety

The relay shall not permit any closure in automatic mode when:

1. Line-to-Ground fault is detected in any of the transformer

or network terminals.

2. Line-to-Line fault is detected between the transformer

terminals or network terminals.

3. Crossed-phase is detected in the transformer terminals or

in the network terminals.

4. Incorrect phase sequence is detected.

5. Rolled phase is detected.

6. Any one phase is dead in the transformer or network

terminals.

Table 5. Trip Amperage as a Function of Percent of CT Primary,

from .05 – 5%

Note: This table represents only that region from .05 – 5% of the CT

primary. The relay can be adjusted up to the 5% level if desired. The

ampere values listed are based upon the standard rating of current

transformers being applied to the appropriate rating of network

protector.

MPCV Relay

Addendum to IB-35-581B

The following set points are additions to IB-35-581B dated

October, 1997.

These set points appear on the pendant screen between the

INCOM ADR and YEAR set points, but were not noted on

Page 8 of IB-35-581B.

INCOME CODE=1999

If the INCOM CODE displays 1999, this indicates that the

relay is communications ready. If a hexadecimal value

appears, this indicates that relay communications have been

turned off.

Note: If a MPCV Relay is provided with communications turned off,

communications can be activated in the field by a qualified Eaton ser-

vice representative.

INCOM SETPT=ON

The default setting is ON with the capability to change to

OFF. If the INCOM SETPT=OFF, this prevents a user from

remotely changing set points through the IMPACC Series

III

or PowerNet software.

INCOM OPEN=ON

The default setting is ON with the capability to change to

OFF. If the INCOM OPEN=OFF, this prevents a user from

remotely opening the breaker through the IMPACC Series

III

or PowerNet software. This also effectively disables the set

point download as well, as the breaker must be ROBO’d

(Remote Open, Blocked Open) before any set points can suc-

cessfully be downloaded.

INCOM CLOSE=ON

If the INCOM CLOSE=ON, this permits a protected remote

close status which reduces the ML value to its operational

lowest point for a time period of 10 seconds. This requires

PowerNet software to enable this feature. Changing this

setting to OFF locks out the remote close feature.

For more information on Cutler-Hammer Network Protectors,

please contact us at 1-800-525-6821.

Percent

of CT

Primary

Network Protector Rating
800

1200

1600/

1875

2000/

2250

2500/

2825

3000/

3500

.05

.07

0.4

0.56

0.8

0.60

0.84

1.20

0.80

1.12

1.60

1.00

1.40

2.00

1.25

1.75

2.50

1.50

2.10

3.00

1.6

2.4

3.2

4.0

2.40

3.60

4.80

6.00

3.20

4.80

6.40

8.00

4.00

6.00

8.00

10.00

5.00

7.50

10.00

12.50

6.00

9.00

12.00

15.00

Trip Amperage

Содержание MPCV Series

































Результаты поиска

Содержание MPCV Series

Отзывы:

Похожие инструкции для MPCV Series

Бренды по названию

Популярные бренды

Eaton MPCV Series, Инструкция пользователя

Результаты поиска

Содержание MPCV Series

Отзывы:

Похожие инструкции для MPCV Series

Бренды по названию

Популярные бренды