Eaton MPCV Series Скачать руководство пользователя

Страница: 14 / 32

Instruction Booklet

IB02402001E

December 2010

Instructions for the Eaton Type

MPCV Network Protection Relay

EaToN CoRPoRaTIoN www.eaton.com

For more information visit: www.EatonElectrical.com

IB02402001E

Instruction Bulletin

Page

Effective: September 2004

Instruction for the

Cutler-Hammer Type MPCV

Network Protection Relay

Testing

Electrical: The relay shall be tested for critical parameters over

the temperature range of -40°C to +120°C for 24 hours.

Submergibility: Waterproof to 0.5 atmosphere.

Burn-in

Each relay is burned-in for 24-hour period including 5 hours at

-40°C, 5 hours at 85°C, and 1 hour at 120°C, 10 hours at

25°C and ramp time is 4 hours.

Settings

All settings can be edited through a digital pendant, which

plugs into the unit while the relay is powered. The trip and

close operations along with remote communications are inhib-

ited and the float light is flashing while editing.

System Voltage (Metered)

216, 380, 400, 416, 433, 480, 600 volts.

Operating Frequency

50 Hz, 60 Hz

Phase Rotation

ABC, CBA

CT Ratio

800, 1200, 1600, 2000, 2500, 3000, 3500

Close Characteristic Line

ST ML (ON, Straight Line), Circular (ST ML is OFF).

Phasing Voltage

ML: 0.5 V to 5.4 V,

Increments: 0.10, 0.20

Phasing Line

PL: +5°, 0°, -5°, -10°, -15°, -25°

Increments: 5°

LH ML: +60° to +90°

Increments: 5°, 10°

Dead Network

Network voltage must be equal or less than 7 volts.

Trip Current

Sensitive, RT: 0.05 to 5% (2.5 to 250 mA)

Increments: 0.01, 0.20

Insensitive (Overcurrent, OC): 0 to 250% (0 to 12.5

amperes).

A minimum of 1% OC when time delay is set other than zero.

Increments: 1, 20

Time Delay

TD: 0 — sensitive mode, no instantaneous overcurrent pickup.

TD: 0.25 to 300 seconds, instantaneous overcurrent pickup is

enabled.

Increments: 0.25 second, 20 seconds.

TD: INF disables the sensitive setting, set the time delay to

infinite and only permit tripping on insensitive OC value.

Watt-Var

Enable: On, Off

Angle: 60°

Pump Protection

Enable: On, Off

Breaker Cycles: 3 to 20

Increments: 1, 5

Pump Time: 30 to 300 seconds

Increments: 1, 10

Reset Time: 15 to 60 minutes

Increments: 1, 10

Auxiliary Input

Enable: On, Off

Enable, Disable

Contact: NO (Normally Open), NC (Normally Closed).

Tolerances

The relay shall operate within the tolerance shown while

operating over the normal temperature range of -20°C to

+110°C and the normal network voltage range of 12 to 190

Vac.

Sensitive Trip: ±5% of setting or ± 0.5 mA, whichever is

greater.

Instantaneous Trip: ±5% of setting or ±0.1 A, whichever

is greater.

Insensitive Trip: ±5% of setting or ±0.1 A, whichever is greater.

Time Delay: ±1% of setting.

Phasing Voltage: ±5% of setting or ± 0.2 volts, whichever

is greater.

Phasing Angle: ±1 degree of setting.

Phase Compensation Angle: ±2 degree of setting.

Trip and Close Angle: ±1 degree of setting.

Operation

Automatic Trip

The trip contacts shall close within 5 cycles of reverse cur-

rent detection. The magnitude and direction of the current

must exist for at least 2 cycles to initiate trip operation.

Sensitive — The relay shall permit a trip when the reverse

current is in the trip region and magnitude is equal or greater

than the sensitive current setting.

Insensitive — The relay is set to insensitive mode when TD is

set to INF.

Time Delay — The delay starts when reverse current is in the

trip region and has a magnitude equal or greater than the

sensitive current setting. The delay stops when the current is

less than the sensitive current setting. The relay shall also ini-

tiates an instantaneous trip when the reverse current is equal

or greater than the overcurrent setting.

Watt-Var — The relay rotates the trip region by 60° and

initiates a trip when the instantaneous reverse current is

equal or greater than the overcurrent setting.

Manual (Remote) Trip

Initiated via PowerNet by a ROBO (Remote Open Block Open)

command. The relay shall not permit any trip or close opera-

tion while the command is active. The Clear ROBO command

will allow the relay to assume normal automatic mode.

Automatic Close

The relay shall permit a closure when the phasing voltage

is in the close region and the magnitude is equal or greater

than the phasing voltage setting, ML. The close contacts shall

close within 5 cycles of phasing voltage detection. The mag-

nitude and direction of the voltage must exist for at least 30

cycles to initiate close operation.

Содержание MPCV Series

































Результаты поиска

Содержание MPCV Series

Отзывы:

Похожие инструкции для MPCV Series

Бренды по названию

Популярные бренды

Eaton MPCV Series, Инструкция пользователя

Результаты поиска

Содержание MPCV Series

Отзывы:

Похожие инструкции для MPCV Series

Бренды по названию

Популярные бренды