Eaton Matrix Telecom Inverter System Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 86

background image

Matrix Telecom Inverter System

22

Copyright © 2008-2010 Eaton Corporation. All Rights Reserved.

IPN 997-00012-68D February 2010

Step 2 - Controller DC input wiring

Controller module and interface module are powered from inverter modules.
Either:

•

If 100A STS is fitted:
Use the supplied 3-pin power cables to connect from CN12 on the
controller backplane to CN6 on the STS backplane, and from CN7 on the
STS backplane to CN9 on the inverter shelf backplane.

•

Otherwise:
Use the supplied 3-pin power cable to connect from CN12 on the
controller/interface/STS shelf backplane to CN9 on the inverter shelf
backplane.

"

CN9 connector on inverter backplane

#

CN12 connector on controller/interface
shelf.

Step 3 - Controller CAN bus wiring

Use the supplied signal cable to connect from CN3 on the controller/interface
shelf backplane to CN8 connector on the inverter shelf backplane.

"

CN3 connector on controller/interface shelf

#

CN8 connector on inverter backplane

«
...
26
27
28
29
30
...
»

Содержание Matrix Telecom Inverter System























































































Отзывы:

Нет отзывов

Похожие инструкции для Matrix Telecom Inverter System

Бренд: Xantrex Страницы: 76

blueplanet 29.0 TL3 Series

Бренд: Kaco Страницы: 64

Бренд: Datalogic Страницы: 2

ENC58-H15 Series

Бренд: Datalogic Страницы: 2

Бренд: Oakley Страницы: 11

GUARDIAN SERIES

Бренд: Generac Power Systems Страницы: 12

Бренд: EINHELL Страницы: 10

Бренд: Inorea Страницы: 104

Evolute RTLA50-S

Бренд: Renishaw Страницы: 11

Auto-Link-SPE-G

Бренд: I-novative Страницы: 10

Бренд: Suaoki Страницы: 32

Бренд: Patton electronics Страницы: 7

Бренд: Sencore Страницы: 126

Бренд: ifi Страницы: 2

EZWALL-pro 3x3 v3

Бренд: SmartAVI Страницы: 14

Frenic Mini FRN001C1E-2U

Бренд: Fuji Electric Страницы: 196

Бренд: Lindy Страницы: 14

Бренд: Must Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды