Eaton Matrix Telecom Inverter System Скачать руководство пользователя страница 69

Страница: 69 / 86

STS/MBS Operation

IPN 997-00012-68D February 2010

Normal Operation (mains priority)

Normal Operation (NORM)
Mains priority:

•

Mains AC powers the load
through the static switch

•

MBS can be switched to
Mains Static Switch or
Inverter Static Switch
position

•

SCR2 open, SCR1 and Back-
feed Relay closed

•

If the mains voltage or
frequency is abnormal, but
the inverter is normal, the
STS will transfer to on-line
mode

•

If SCR2 is short, the STS
will keep the off-line mode

Normal Operation (NORM) (inverter priority)

Normal Operation (NORM)
Inverter priority:

•

Inverters power the load
through the STS

•

MBS can be switched to
Mains Static Switch or
Inverter Static Switch
position

•

SCR1 open, SCR2 and Back-
feed Relay closed

•

If the Inverter’s voltage or
frequency is abnormal, but
the mains is normal, the
STS will transfer to off-line
mode

•

If SCR1 is short, the STS
will keep the on-line mode,
and the Back-feed relay will
open

Содержание Matrix Telecom Inverter System















































































Результаты поиска

Содержание Matrix Telecom Inverter System

Отзывы:

Похожие инструкции для Matrix Telecom Inverter System

Бренды по названию

Популярные бренды

Eaton Matrix Telecom Inverter System, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Matrix Telecom Inverter System

Отзывы:

Похожие инструкции для Matrix Telecom Inverter System

Бренды по названию

Популярные бренды